Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Do not expose your product to fire, explosive or other hazardous conditions. There is a slight chance that your phone could be damaged by an electrical storm. We recommend that you unplug the power and telephone line cord for the duration of the storm. On-Air 2100 Classic ~ 1st Edition ~ Issue 2 ~ 11th November ’02 ~ 5051 Setting up Please note that your handset is already registered to the base station. Plan the location Situate your product close enough to the telephone and mains power sockets so that the cables will reach. The only way to disconnect the product from the power supply is to remove the power adaptor from the mains power socket. Therefore you must ensure you plan the location so that the mains power is easily accessed. Make sure it is at least 1 metre away from other electrical products to avoid interference. Do not situate the product in the bathroom or other humid areas. Important You must thread the power supply cable into the socket on the underside of your base. The power cable connector and socket are coloured red. 1 Connect the power supply and switch on. PLINTH WARNING Please take care that the power supply and telephone line cord are connected to the correct sockets as incorrect placement could damage your equipment. Once connected, put the plinth back on the base to prevent it from rocking on the table. There are two positions for the plinth when joining it to the base, both can be used for desk mounting and one for wall mounting. Position A is for desk mounting only and position B is for desk or wall mounting (see Wall mounting on page 25). BA Rubber feet Hold the black plastic square between thumb and forefinger and peel off individual feet from backing sheet as shown. These are to stop your base from moving and to protect your work surface. If you decide on position B, place 2 of the rubber feet on the plinth and 2 on the base. On-Air 2100 Classic ~ 1st Edition ~ Issue 2 ~ 11th November ’02 ~ 5051 Plug the power adaptor into the wall socket and switch on. When the power is switched on, the button on your base will light up. 2 Charge the battery in the handset for at least 16 hours WARNING Do not connect the telephone line cord to the phone socket until your handset is fully charged. This will prevent the risk of the phone being answered before the battery is charged. Answering the phone before the battery is fully charged may prevent it from reaching its optimum capacity. WARNING Under no circumstances should non-rechargeable batteries be used. Only use the approved batteries. Using unapproved batteries will invalidate your guarantee and may damage the telephone. Under ideal conditions the battery should give about 10 hours talk time and 120 hours standby when the batteries have been fully charged. Fully discharging the batteries at least once a week will help them to last as long as possible. However, the charge capacity of rechargeable batteries will reduce with time as they wear out, so reducing the talk/standby time of the handset. Eventually they will need to be replaced. New batteries can be obtained from the Helpline on 0870 240 4682. When the battery has been charged for at least 16 hours the display will show the symbol; you can then connect the telephone line cord to the base. Empty 1/32/3 Full Battery low warning If the handset battery symbol is empty and you hear warning beeps, you will need to recharge your handset before you can use it. Battery performance Your handset is supplied with NiMH batteries. These need to be initially charged continuously for 16 hours to reach full charge. Note that the battery charge icon does not indicate the correct level when the batteries are first installed. The batteries must first be fully charged. Helpline If you are experiencing difficulty, please call the BT On-Air Helpline on 0870 240 4682. On-Air 2100 Classic ~ 1st Edition ~ Issue 2 ~ 11th November ’02 ~ 5051 To replace the handset battery If you need to replace the handset battery, slide off the battery cover. Remove the old battery by disconnecting the small plug inside the battery compartment. 5 Attach the belt clip Connect the plug of the new battery. Slot Replace the battery cover. Please pay attention not to damage the Fit the belt clip onto the back of the handset. charging contacts on the handset. 3 Connect the telephone line cord (after charging your handset) Plug the line cord into the telephone wall socket. 4 Changing your handset fascias There are 3 removeable handset fascias to choose from. Simply slide the fascias off and replace with another. On-Air 2100 Classic ~ 1st Edition ~ Issue 2 ~ 11th November ’02 ~ 5051 Using the telephone To switch the handset power on and off Press and hold the GREEN PHONE button until the display check sequence has happened and only the battery icon is displayed. If you release the button before this has happened the handset will remain switched off. Press and hold the RED PHONE button to switch the handset off. Call timer Your hand...