Log:
Évaluations - 4, GPA: 4.8 ( )

Instructions Binatone, Modèle 2300

Fabricant : Binatone
Taille : 4.43 mb
Nom Fichier : concept-combo-2300-corded-ug_uk-btp_v03_dec26-07.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


To Turn key tones on/off 26 .. To Set flash (Recall) time 26 .. To Set Dialling Mode (Tone/Pulse) 27 .. To Set Base to default settings 27 .. To Change the PIN code 28 Troubleshooting 29 Cleaning and Care 31 Declaration of Conformity 31 Guarantee and Service 32 Technical Details 33 Connection and conditions for use. You can connect your Concept Combo 2300 to a direct exchange line (DEL) - a line connected to a local exchange, with its own phone number; to an extension on an approved compatible PBX. Do not connect the Concept Combo 2300 as an extension to a payphone. The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.) connected to an exchange line must not add up to more than 4 - otherwise, one or more of them may not ring and/or answer calls correctly. The Concept Combo 2300 has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise. Binatone Help Line : 0845 345 9677 4 Read First Before Use Choosing a site for the base unit and charger pod The base unit and charger pod(s) should be placed on a level surface, in a position where: .. the mains adapter plug will reach an easily accessible 230-VAC switched mains supply socket - never try to lengthen the mains power cable .. the base unit's telephone line cable will reach your telephone line socket or extension socket .. it is not close to a sink, bath or shower, or anywhere else where it might get wet .. it is not close to other electrical equipment -fridges, washing machines, microwave ovens, fluorescent lights, televisions etc. .. if the base comes into contact with liquids, disconnect it promptly and use a soft cloth to dry it; if you believe that the liquid has seeped into the unit, do not reconnect the base station. Contact the Binatone helpline. .. it is away from hot, humid conditions and strong sunlight Mains power connection IMPORTANT - The CC2300 base unit must be used with the mains adapter supplied with the unit. Using any other adapter will result in non-compliance with EN60950, and will invalidate any approval given to this apparatus. If you have a Broadband line If you connect your telephone to a line with a broadband connection, you will need to insert a micro-filter between the telephone and the telephone line; otherwise you may get interference between the telephone and the broadband, which could cause problems. In a home with broadband, every telephone must have a micro-filter connected, not just the one at the telephone point that your modem is connected to. If you need more broadband micro-filters, contact your broadband supplier. Binatone Help Line : 0845 345 9677 5 Installation and Set-up 1/ Choose a suitable site for the base unit (see page 5) 2/ Connect the mains power lead and the telephone line cord into the base unit Plug one end of the telephone line cord into the jack on the back of the base (the other end will plug into the telephone wall socket later) 3/ Plug the mains adaptor into your wall socket. If you have one or more charger pods, Seethenoteonpage5 plug the mains adaptors accordingly Make sure that the 230VAC, 50hz mains socket is switched OFF when you plug the mains adapter into the socket. Seethenoteonpage5 4/ Connect the base unit to the telephone line Insert the telephone line plug into the socket then switch mains power back ON. Make sure the mains socket is switched on — the phone won’t work without electrical power Binatone Help Line : 0845 345 9677 6 Desk/Wall mount installation To place the CC2300 on a desk, connect the stand to the bottom of the phone in the slots near the rear of the base as shown below. Desk Mount Insert the rigid clips of the stand into the slots on the bottom of the phone (nearer the centre of the base ). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. Wall Mount To place the CC2300 on a wall, connect the stand to the bottom of the phone in the slots near the front of the base as shown below. Binatone Help Line : 0845 345 9677 7 Desk/Wall mounting continued... Insert the rigid clips of the stand into the slots on the bottom of the phone (nearer the centre of the base). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. Mark two points on the wall that are 77 mm apart to lay the fixing centers as shown below. BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws at the marked locations, leaving approximately 7mm between the wall and the the screw head. Hang the telephone on the screws using the wall mount slots. You may need to remove the telephone from the wall and tighten the screws so that the telephone is securely fixed and does not wobble. Place the Handset on the cradle with the parking hook on the cradle arranged to fit in ...

Ce manuel est également adapté pour les modèles :
Téléphones sans fil - 2300 (4.43 mb)
Téléphones sans fil - 2300 (4.43 mb)
Téléphones sans fil - 2300 (4.43 mb)
Téléphones sans fil - 2300 (4.43 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories