Évaluations - 5, GPA: 4 ( )

Fabricant : Cortelco Taille : 245.72 kb Nom Fichier : 6066331e-47dc-4be4-917a-64d5d983ef47.pdf Langue d'enseignement:

When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. e. If the product has been dropped or cabinet has be damaged. f. If the product exhibits a distinct change in performance. 13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning. 14. Do not use the telephone to report a gas leak in the vicinity of the leak. 15. This power unit is intended to be correctly oriented in a vertical or floor mount position. 16. Plug the power adaptor into an electrical outlet that is near the equipment and easily accessible. SAVE THESE INSTRUCTIONS Safety Instructions for Handset Battery Pack CAUTION: There is a danger of explosion if battery is incorrectly replaced. Use only an approved battery pack in the handset of your Cordless Telephone. To reduce the risk of fire or injury, always do the following when replacing, discarding, or charging battery. When handling the batteries, be careful not to short the battery with conducting materials such as rings, bracelets, and keys. The Battery or conducting material may overheat and cause burns. Use only the following type and size of battery pack: FOR HANDSET UNIT: GP60AAAH3BMXZ 3.6V 600mAh GPI INTERNATIONAL LIMITED CONTAINS NICKEL-METAL HYDRIDE BATTERY. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY 1. Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal instructions. 2. Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 3. Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets and keys. The battery or conductor may overheat and cause burns. 4. Charge the batteries provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual. 5. Observe proper polarity orientation between the battery(ies) and battery charger. 6. Do not mix old and new batteries in this product. 7. Do not mix batteries of different sizes or from different manufacturers in this product. SAVE THESE INSTRUCTIONS 100 mmBoth wall mount screws are Dia. 4.0 mm X 24 mm Connecting the wall mount bracket (See “Getting Started” on page 8) PART I 586002TP227F FEATURES Caller ID (subscription required) 5 Number Redial Call Waiting (subscription required) Base to Handset Page Illuminated Handset Display Auto Answer out of Cradle Clock 2-Way Intercom (requires 2 Handsets) Call Timer Mute 40 Name & Number Phonebook Headset Jack (2.5 mm) 6 Handset Capability Tone / Pulse Dialing 1 Handset and Base Layouts Layout of Handset Function Keys 1. Antenna 8. Intercom (>) 2. Earpiece 9. Volume Down (Ў) 3. Display (LCD) 10. Flash 4. Menu / OK 11. Caller ID 5. Delete / Mute (Power) 12. Talk / Hang Up 6. Redial / Volume Up (^) 13. Speakerphone 7. Phone Book (<) 14. Dialpad Layout of Base Functions 1. Page 2. Antenna 3. In Use/Message Waiting 4. Charge 2 Getting Started Install and Charge the Battery Pack 1. Open the battery cover by gently pressing down on the top of the cover while sliding it down. 2. Plug the Battery Pack connector into the Handset socket, and then place the battery pack and wires in the compartment. The printing on the pack should be upright and facing you, with the battery wires coming from the upper right edge of the battery pack. 3. Tuck the wires between the right side of the pack and the wall of the compartment. Replace the battery cover by lining up the four tabs with the corresponding slots, and sliding it up until it locks into place. 4. Attach the belt clip, if desired. If you are wall mounting the Base, connect the DC power cord and telephone line cord to the Base, and then attach the wall mount bracket. Run the two cords through the rectangular hole located on the back of the bracket, or through the channel located on the bottom of the bracket. 5. Connect the power adapter to the Base and a live outlet. Make sure a switch does not control the outlet. The outlet should be near the Base Unit, and easily accessible. DO NOT connect the telephone line cord to your live telephone jack until the Handset is fully charged. 6. Place the Handset in the Base cradle. The Handset and Base communicate with each other automatically. This is the Registration process, and it may take up to 60 seconds. 7. Allow the Handset to charge for a day for the first time charging. The CHARGE indicator on the Base will glow while ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :