Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
• Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack. • Make sure the battery pack is installed correctly. • If the screen displays , place the handset in the base and charge for at least eight hours. • If the battery does not charge after eight hours, replace it with AT&T Battery 3301, SKU# 91076. PROBLEM SOLUTION If you have no dial tone: Check all the previous suggestions. If you still do not hear a dial tone, disconnect the phone and try another phone in the same jack. If there is no dial tone on that phone either, the problem is probably in your wiring or local service. 5 4 TELEPHONE OPERATION TELEPHONE OPERATION PROBLEM SOLUTION If you hear a triple-beep The handset and base are not signal when you try to communicating properly. You might use the handset: be out of range. Move closer to the base and try again. PROBLEM SOLUTION If you hear noise or • You may be out of range. Move closer interference when to the base. using the phone: • Household appliances plugged into the same circuit as the base can sometimes cause interference. Try moving the appliance or the base to another outlet. • The layout of your home or office may be limiting the operating range. Try moving the base to another location, preferably on an upper floor. • Using the handset near household appliances (microwaves,computers, televisions,stereos,etc.) can sometimes cause interference. Move away from appliances while using the handset. PROBLEM SOLUTION If the phone does not • Make sure the ringer is on. ring when you receive • Make sure the telephone line cord is a call: connected firmly to the base and the telephone jack. • Make sure the AC adapter is plugged firmly into an electrical outlet not controlled by a wall switch. • You might be too far from the base; move closer. •You might have too many extension phones on your telephone line to allow all of them to ring. Try unplugging some of them. 5 5 TELEPHONE OPERATION TELEPHONE OPERATION PROBLEM SOLUTION If your telephone misdials: • If you have dial pulse (rotary) service, you’ll need to set the dial method to . Follow the instructions under “Set Dial Method”in the FEATURE SETUP section of this manual. • If you have touch tone service and you hear clicks while you are dialing, you’ll need to set the dial method to . Follow the instructions under “Set Dial Method”in the FEATURE SETUP section of this manual. PROBLEM SOLUTION If you are unable to operate special telephone services or other equipment requiring touch tone signals: If you have dial pulse (rotary) service, follow the directions under “Temporary Tone Dialing”in the TELEPHONE OPERATION section of this manual. CALLER ID PROBLEM SOLUTION If the caller’s name or • Make sure you subscribe to Caller ID phone number is not service from your local telephone displayed: company. • Make sure the battery is charged. • Caller ID service might not work when the phone is connected to a Private Branch Exchange (PBX). 5 6 CALLER ID CALLER ID PROBLEM SOLUTION If the caller’s name or • You should call your service provider to phone number is not confirm that you subscribe to combined displayed during Caller ID with Call Waiting service. Call Waiting: • Caller ID information received during Call Waiting is displayed only on the handset that is in use. The information is stored in the Caller ID log on ALL registered handsets. • Make sure the battery is charged. ANSWERING SYSTEM PROBLEM SOLUTION If messages are incomplete: • If a caller leaves a very long message, part of it may be lost when the system disconnects the call after four minutes. • If the caller pauses for more than seven seconds,the system stops recording and disconnects the call. • If the system’s memory becomes full during a message,the system stops recording and disconnects the call. PROBLEM SOLUTION If you have difficulty hearing messages: Check the volume setting. 5 7 ANSWERING SYSTEM ANSWERING SYSTEM PROBLEM SOLUTION If the system does not • Make sure that the answering system answer after the correct is on. number of rings: • If Toll Saver is on,the number of rings changes to two when you have new messages waiting. • In some cases,the system may be affected by the ringing system used by the local telephone company. • If the memory is full or the system is off, the system answers after 10 rings. PROBLEM SOLUTION If appears in the message window: You need to reset the clock. See “Set the Clock” in the ANSWERING SYSTEM OPERATION section of this manual. PROBLEM SOLUTION If the system does not respond to commands from a remote touch tone phone: • Make sure you are calling from a touch tone phone. When you dial a number, you should hear tones. If you hear clicks instead,the phone is not a touch tone telephone. • Make sure you enter your Remote Access Code correctly. • There may be noise or interference on the phone line you are using. Press keys firmly. 5 8 ANSWERING SYSTEM ANSWERING SYSTEM PROBLEM SOLUTION If your outgoing • When you r...