Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
9) TALK Indicator (p. 10, 12) (TALK) Button (p. 12, 17) Headset Jack (p. 29) [CH) (Channel) Button (p. 13) [TONE] Button (p. 27) [FLASH) Button (p. 26, 28) Antenna INTERCOM Indicator (p. 24) y Navigator Key /(S,S. PROGRAM ¡3, AUTO (B) (p. 10, 11, 13, 18, 28) [DIRECT] Button (p. 22, 23) [INTERCOM) Button (p. 24) REDIAL/PÀUSË1 Button (p. 13, 27) Charge Contacts (p. 9) 6 Base unit Antenna (p. 3, 8) ÎTÔNË1 Button (p. 27) Charge Contacts (p. 9) VOLUME 0, 0 Buttons (p. 15) IN USE/CHARGE Indicator (p. 9, 20) (LOCATOR/INTERCOM ] Button —rjy—y AUTO/PROGRAM] /// Button (p. 20) [PAUSE] Button (P- 27) (FLASH) Button (p. 26, 28) i HOLD/RINGER) Button (p. 11, 15) DIGITAL SP-PHONE) (Speakerphone) Button and Indicator (p. 14) (REDIAL) Button (p. 15) (P- 24) MIC (Microphone) (p. 14, 24) 7 Settings Connections •USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z). •The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) •To connect a standard telephone on the same line, see page 33. 8 * Installing the Battery in the Handset Install the battery and close the handset cover, locking it into the place. Battery Charge Place the handset on the base unit and charge for about 6 hours before initial use. •The IN USE/CHARGE indicator lights. IN USE/CHARGE Indicator Recharge When the RECHARGE indicator flashes or the unit beeps intermittently, place the handset on the base unit to recharge the battery for 6 hours. •If you DO NOT recharge the handset battery for more than 15 minutes, the RECHARGE indicator will continue to flash. Battery information After your Panasonic battery is fully charged: Operation Approx. battery life While in use (TALK) near the base unit* Up to about 6 hours away from the base unit Up to about 4 hours While not in use (Standby) Up to about 14 days ‘Within about 10 feet (3 m) •Battery life may vary depending on usage conditions and ambient temperature. •Clean the handset and the base unit charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly. •If the battery is fully charged, you do not have to place the handset on the base unit until the RECHARGE indicator flashes. This will maximize the battery life. •The battery cannot be overcharged. Selecting the Dialing Mode If you have touch tone service, set to TONE. If rotary or pulse service is used, set to PULSE. Your phone comes from the factory set to TONE. The TALK and DIGITAL SP-PHONE indicator lights must be off before programming. Use the handset near the base unit. 1 2 3 Press PROGRAM ® •The TALK indicator flashes. Press AUTO ®. To select PULSE, press (#) twice. OR To select TONE, press (3 twice. Press PROGRAM ® •A beep sounds. •To cancel during programming, press PROGRAM (2)- Start again from the beginning. • If 3 beeps sound during programming, a wrong key was pressed. Start again from the beginning. 10 Selecting the Ringer Volume With the handset The TALK indicator light must be off. •To select HIGH (preset) or LOW, press (B or IB- Each time you press (B or B> the ringer volume will change and the selected volume will ring. •To turn the ringer OFF, press and hold ® unt'l 2 beeps sound. •To turn the ringer ON, press ®. The ringer will sound at the HIGH level. s.® •When you replace the battery, the selected ringer volume setting will return to the factory set. Reprogram if necessary. With the base unit The TALK and DIGITAL SP-PHONE indicator lights must be off. •To select HIGH (preset) or LOW, press (HOLD/RINGER]. Each time you press the button, the ringer volume will change and the selected volume will ring. •To turn the ringer OFF, press and hold i HOLD/RINGER) until 2 beeps sound. •To turn the ringer ON, press [HOLD/RINGER], The ringer will sound at the HIGH level. i Making Calls With the Handset To have a hands-free conversation, connect the headset to the handset (p. 29). 1 Press (TALK). •The TALK indicator lights. 2 Dial a phone number. 3To hang up, press [TALK] or place the handset on the base unit. •The indicator light goes out. • If an alarm tone sounds in step 1, move closer to the base unit or place the handset on the base unit. Then try again. 12 * To redial the last number dialed on the handset Press [TALK) [REDIAL/PAUSE j To select the handset receiver volume 3 levels (HIGH, MEDIUM, LOW) are available. Press Q or (3 while talking. • Each time you press ] or (3. the volume level will change. •When you replace the battery, the selected receiver volume setting will return to the factory set (MEDIUM). Reprogram if necessary. If noise interferes with the conversation Press icFp to select a clearer channel or move closer to the base unit. Lighted handset keypad The handset dialing buttons will light when you press a button or lift the handset off the base ...