Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
When finished, press f PROGRAM/2WAY RE~C]. Setting the Greeting Monitor Function When your greeting message is being played to the caller, you can also listen to it through the base unit speaker. To listen to your greeting, set to “2 (ON)”. The factory preset is “1 (OFF)”. 1. Press [PROGRAM/2WAY RECl 2. Press f SCREEN/PLAYBACK], 3. Press (4)- •The current setting, “1” or “2”, is displayed on the base unit. 4. To select “2 (ON)”, press OR To select “1 (OFF)”, press (T|. •The setting is displayed. 5. When finished, press (PROGRAM/2WAY RECl. Making Calls 1 Press [talk]. •The TALK indicator lights. 2 Dial a telephone number. • If you misdial, press (FLASH) firmly then dial again. To hang up, press (TALK) or place the handset on the base unit. •The indicator lights go out. ’°o w- (TALK) and Indicator '(HOLD] [LOUD] (REDIAL/PAUSE] fCHl I FLASH I • If an alarm tone sounds in step 1, move closer to the base unit or place the handset on the base unit. Then try again. •To switch to the speakerphone during a call with the handset, see page 26. To redial the last number dialed Press [TALK] * (REDIAL/PAUSE]. To select the handset receiver volume Press [LOUD] while talking. • Each time you press the button, the volume level will change from MEDIUM (preset) to HIGH to LOW. 22 If noise interferes with the conversation Press [CH] to select a clearer channel or move closer to the base unit. To put a call on hold Press (hold). •The TALK indicator and the SP-PHONE indicator flash simultaneously. •After 6 minutes, warning tones will sound every about 16 seconds. After a total of 10 minutes, the call will be disconnected. To release the hold From the handset, press [TALKl. From the base unit, press [DIGITAL SP-PHONE]. • If another phone is connected on the same line (p. 55), you can also release the hold by lifting its handset. Lighted handset keypad The dialing buttons will light while dialing and flash when a call is received. The lights will go out about 10 seconds after dialing or answering a call. Answering Calls With the Handset If the handset is off the base unit, press [TALK). •You can also answer a call by pressing any dialing button 0 to 9, *, or # (—Any Key Talk). OR If on the base unit, just lift up. With the Base Unit (Digital Duplex Speakerphone) 1 2 3 Press (DIGITAL SP-PHONE]. •The DIGITAL SP-PHONE indicator lights. Talk into the MIC (microphone). To hang up, press [DIGITAL SP-PHONE). •The indicator light goes out. 24 ■While using the speakerphone, if the handset is on the base unit, you may switch to it by lifting it up. Hands-Free Digital Duplex Speakerphone The digital duplex speakerphone enhances your telephone conversation. For best performance, please note the following: • Use the speakerphone in a quiet room. • Speak alternately with the caller. • If the caller complains that your voice is hard to hear, press VOLUME© to decrease the speaker volume. • If the other party’s voice from the speaker cuts in/out during a conversation, press VOLUME ©to decrease the speaker volume. To adjust the speaker volume (8 levels) while talking To increase, press VOLUME ©. To decrease, press VOLUME 0. To put a call on hold Press (HOLD/RINGERl •The DIGITAL SP-PHONE indicator flashes. •After 6 minutes, warning tones will sound every about 16 seconds. After a total of 10 minutes, the call will be disconnected. To release the hold From the base unit, press [DIGITAL SP-PHONE). From the handset, press [TALK] or lift the handset off the base unit. •You may also press (REMOTE SP] on the handset to release the hold at the base unit. • If another phone is connected on the same line (p. 55), you can also release the hold by lifting its handset. 25 Remote Speakerphone You can switch a call with the handset to the speakerphone easily. 1 Handset: During a call with the handset, press [REMOTE SP). •The call switches to the base unit. •The INTERCOM indicator flashes. •The DIGITAL SP-PHONE indicator lights. 2 Base unit: Talk into the MIC. 3Base unit: To hang up, press (DIGITAL SP-PHONE], •The indicator lights go out •You can also hang up by pressing (REMOTE SP). MÍC ! When using (REDIAL/PAUSE), dialing a stored number (p. 29), etc., i press [REMOTE SP) after dialing is completed. INTERCOM Indicator ÍTALK TREMOTE SP) f€r Ooq t °oo 26 You can turn on the base unit speakerphone using the handset. Making calls with the remote speakerphone 1. Handset: Press (REMOTE SP). 2. Handset: Dial a telephone number. 3. Base unit: Talk into the MIC. 4. Handset: To hang up, press (REMOTE SP), •You may also hang up by pressing (DIGITAL SP-PHONE). To switch to the handset (while using the remote speakerphone) Press (talk]. •You can continue the conversation using the handset. •To hang up, press [TALK] or place the handset on the base unit. When using (REDiAL/PAUSEl, dialing a stored number (p. 29), etc., press (TALK) after dialing is complete...
Ce manuel est également adapté pour les modèles :Téléphones filaires - KX-TCM943-B (1.24 mb)