Instructions Avaya, Modèle SPEAKEASY COMBO 2005 TWIN

Fabricant : Avaya
Taille : 1.52 mb
Nom Fichier :

Langue d'enseignement:

Aller à la télécharger

Facilité d'utilisation

The default system PIN code is 0000. 1. Press

and to select BS SETTINGS. 2. Press and to select CHANGE PIN. 3. Press to show PIN? 4. Enter the old system PIN. 5. Press to show NEW PIN?, and enter the new system PIN. 6. Press to show CONFIRM?, and enter the new systemPIN again. Note: If the new PIN entered in Step 6 is not the same as the new system PIN entered in Step 5, you must enter the new system PIN atStep 5 again. 7. Press to confirm. 8.4.5 Reset your Cordless Handset You can reset your phone to the default settings. After reset, all your personal settings, call list entries and redial list entries will be deleted, but your phonebook remains unchanged. 1. Press and to select DEFAULT. 2. Press to show PIN? 3. Enter the 4-digit system PIN (default value 0000). 4. Press to show CONFIRM? 5. Press to confirm, and the phone will be reset to its defaultsettings. 30 . 9 REGISTRATION IMPORTANT: When you purchase your phone system, all handsets are already registered to your base, so you do not need to register them. Handset registration is only necessary when you buy extra handsets or if a handset has become faulty. You can register additional handsets to have up to five handsets per baseunit, with each handset's number (1 to 5) shown on its display. (Note: each handset can only be registered to one base.) To check whether a handset is registered, make sure mains power to the base unit is switched on and the handset is within range. The handset's display should show its number and the should be steadily on. If the display shows "REGISTER", you need to register the handset again using the following process: On the cordless handset: 1. Press and to select REGISTRATION. 2. Press to display “ PIN ?”, enter the 4-digit PIN code for the base (default PIN code is 0000). 3. Press and the display will flash “PLEASE WAIT”. On the base: 4. At the same time, press and hold the key for about 5 seconds or until it beeps, to indicate the base is in registration mode. 5. A confirmation beep is played to indicate successful registration, and the handset returns to idle mode with its handset number displayed and the antenna icon steady. If registration fails, the handset beeps and the display returns to show REGISTER and the antenna icon continues to flash. 31 10 TROUBLESHOOTING If you have difficulty with your phone, please try the suggestions listed below. Problem Cause Solutions No dialling tone when pressing the key a. The connection cord of the base station is not plugged in. b. The adapter cord is not plugged in correctly in the base station. c. The line is busy, as another handset is used. d. Wrong telephone line cord. a. Check the connections. Unplug and plug back in the mains. Check that the telephone line cord has been plugged into the base station and the phone socket. b. Check the base station plug and the 230V plug (remove and plug-in). c. Wait until the line is unoccupied. d. Use the original telephone line cordsupplied. When connected to a PBX, no and/or wrong connection after dialling. Dialling prefix is needed. Insert the dialling prefix "OUT OF RANGE" is displayed. a. Base station out of range. b. Base station not connected to mains. Reduce the range. Connect base station to mains. The call does not work. Service not activated or wrong operator or wrong setting Check your Subscription with network or change the dial mode. No display. ...

Ce manuel est également adapté pour les modèles :
Téléphones sans fil - SPEAKEASY COMBO 2005 TWIN (1.52 mb)
Téléphones sans fil - SPEAKEASY COMBO 2005 TRIPLE (1.52 mb)
Téléphones sans fil - SPEAKEASY COMBO 2005 TRIPLE (1.52 mb)
Téléphones sans fil - SPEAKEASY COMBO 2005 TRIPLE (1.52 mb)

Voir tous