Évaluations - 5, GPA: 3.8
(
)
)
|
Facilité d'utilisation
• Wear safety glasses. Your Multi-Code Radio Controls are designed specifically for the remote control of industrial door or gate openers and to give years of dependable service without adjustment. SELECTING A CODE The code is determined by the positions of the 10 small switches numbered 1 through 10 located on the receiver board. To gain access to the switch, remove the top section of the case. Any combination of ON ( CLOSED) or OFF (OPEN) positions can be selected by using a small screwdriver or ball point pen (see figure 1) . We strongly urge that you avoid the following code schemes: ALL ON, ALL OFF, 2, 4, 6, 8, 10, ON or 1, 3, 5, 7, 9, ON. These codes are frequently used by other manufacturers, and create the possibility of false operation, and may be less secure than other code schemes. Be certain to check that the code is functional before completing the installation. CODE SWITCH Figure 1 1 2 3 4 5 6 7 8 9 10 OPEN INSTALLATION The receiver comes equipped with an F-connector receptacle and an antenna with an F-connector plug. The antenna can be plugged directly into receptacle, or it can be moved away from a metal structure, or to an outside location for better receiver performance by using a coaxial kit available from your dealer. Begin your installation of the 1099 by correctly wiring the receiver to the devices you will be using. WE URGE YOU TO BECOME FAMILIAR WITH THE INSTRUCTIONS THAT THE MANUFACTURER OF YOUR EQUIPMENT HAS PROVIDED. SINCE, IN MANY CASES, THESE INSTRUCTIONS WILL DETERMINE THE WAY IN WHICH THE 1099 RECEIVER WILL BE INSTALLED. The receiver should be mounted near the opener power head and can be installed in any position by using screws and the two slots in the cover flanges. Select a location and position that permits access to the terminals and space for the antenna as clear of metal structures as possible and preferably in a vertical position. Wire the red and black wires to a 24VAC/DC power supply. Connect the remaining gray wires as specified by the manufacturer of your operator. If such instructions do not exist, wire the two gray wires in parallel with the pushbutton terminals. If the operator has a three wire terminal, the proper terminals will usually be marked “1” and “2” or “24V” and “RELAY” (see figure 2). At this point you should mount your 1099 receiver to its permanent installation, if you have not already done so. CONTROL BOX RED GRAY GRAY BLACK 1 2 3 Figure 2 (1099-31) RECEIVER ANTENNA INSTALLATION After you have mounted your receiver, test it with the enclosed antenna for range, noting the coverage that you get from all desired operating locations. If greater range or coverage pattern is necessary, you may need Coaxial Wiring Kit, which is available from your dealer. It is not advisable to add lengths of coaxial cable greater than 20 feet, as this may affect range or tuning. ADDITIONAL INSTALLATION INFORMATION Linear Corporation has taken every possible precaution to make the 1099 receiver as reliable as possible. We think the following notes should be observed: 1. Be sure the unit is sealed from moisture, and, if at all possible, keep it away from direct moisture. 2. In those installations where vibration may be a factor, be sure to use a fastening compound, such as LOCTITE (TM) on the mounting screws to insure reliable mounting. 3. If this, or any other equipment is being used in a safety-related device, be sure to test the entire system at the time of installation, and at frequent intervals, to determine that it is working properly. OPERATIONAL CHECK To check operation, move back a reasonable distance (about 50 feet) and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range. If the transmitter is stowed well out of sight, it may be necessary to remove it from its mounting and hold near the windshield. Try different locations and positions. If operation is still unsatisfactory, check the following: 1. The antenna must be connected to the receiver for normal use. 2. If the opener fails to operate, check to see that 115 VAC power is present. Check circuit breakers or for a system power failure. 3. If the opener operates by pressing the wall button, but not when the transmitter button is pressed, the radio controls are probably at fault. Check to make sure both transmitter and receiver code switches are set to the exact same code since a difference of just one switch will prevent operation. Check transmitter battery, location of the transmitter and receiver installation. 4. Try mounting the antenna at a more favorable remote location by utilizing the coaxial kit. If, after performing the above operational check, it is necessary to return the radio controls, return both the transmitter and receiver to your dealer for repair or replacement or they may be returned, postage prepaid, directly to Linear Corporation. WARRANTY All MULTI-CODE garage door related produ...