Log:
Téléchargements : 15   Taille : 740 kb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name@name@name@name

This air pressure usually falls between 40 - 60 psi. Adjust air pressure with trigger pulled and air control knob (if applicable) fully open. If reduced air pressure is desired for some areas of spray job, use air control knob to reduce pressure as necessary (See Figure 3). Before spraying the workpiece, practice a few minutes on a cardboard target to ensure the pattern size and consistency are set correctly. 2 Operating Instructions TL2402 Operation 1. Begin spraying. Always keep the gun at rig

Téléchargements : 2   Taille : 468 kb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name@name@name

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / A Division of Scott Fetzer Co. 100 Production Drive Harrison, Ohio 45030 Telephone: (800) 626-4401 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale or rental) of the Campbell Hausfeld product. 4. WHAT PRODUCTS ARE COVERED UNDER THIS WARRANTY: Any Campbell Hausfeld airless spray gun supplied or manufactured by the Warrantor. 5. WHAT IS COVERED UNDER THIS WARRANTY: Defects in material an

Téléchargements : 6   Taille : 2 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

A minimum of 100 feet of hose should be used. b. Adjust the Engine Speed and Pump Pressure. First set the throttle lever to the maximum RPM setting (fully left). Trigger the gun onto a test paper to check the spray pattern and atomization. Adjust the Pressure Control Knob until you get a good pattern. Reduce RPM of engine to support pressure without overworking engines. 7. Clean tip if clogged. If tip is becoming worn, replace it. Worn tips waste paint, cause overspray, make cutting-in difficult

Téléchargements : 1   Taille : 7 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

5 6 Operating Instructions and Assembly Instructions Airless Paint Sprayers Preparation Airless painting systems, unlike most other power tools, require additional care to ensure proper working order. Following these instructions will significantly increase the likelihood of having a positive paint experience. It is important that the painting equipment is flush/tested EACH time a new job is started. Each pump is tested at the factory with a fluid that must be flushed from the system prior to pa

Téléchargements : 0   Taille : 7 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

TIP SEAL AND WASHER Occasionally, you will need to replace the silver seal and clear washer located inside the tip base. 1. To replace seal and washer, first loosen tip base with adjustable wrench, and then remove by hand. 2. Remove spray tip. 3. With Phillips screwdriver, push seal and washer out from front of tip base. 4. With flat side of seal facing up, place seal in base. Make sure it lines up properly with base. 5. Place washer in base. Make sure it lines up properly with base. 6. Put spra

Téléchargements : 8   Taille : 7 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

Paint requires thinning B. Follow paint manufacturers thinning recommendations. Paint should not typically need to be thinned more than 8 oz. of solvent per gallon C. Reversible Spray Tip in cleaning position C. Turn Spray Tip to Spray position. See Cleaning section for details Pump primes and builds pressure, but does not maintain pressure once trigger is pulled 24.Clogged Suction Filter 25.Suction Assembly loose and/or sealing surfaces are dirty at Inlet Valve 24.Remove Suction Filter and clea

Téléchargements : 0   Taille : 8 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

Suction filter Before each use Every 25 gal. or Yes and every 5 gal. more often if required Gun filter Before each use Every 25 gal. Yes Do not attempt to clean gun filter, only replace. Roller nap Before each use As required Yes Prime/spray valve Before each use Every 1000 gal. Yes 3/4” Wrench, torque to 80 in/lbs. Push button Before each use Every 1000 gal. Yes 7/8” Socket or wrench, torque to 200 in/lbs. Block bolts Before each use Do not require Yes Block bolts are to be torqued to 275 in/lb

Téléchargements : 0   Taille : 8 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

2 ApplicationChart................................. 2 SafetyGuidelines................................. 3 GeneralSafetyInformation ........................ 3 AssemblyInstructions ............................. 6 Preparation...................................... 6 SprayingInstructions.............................. 8 Cleanup........................................ 10 Storage........................................ 14 SprayGunMaintenance.......................... 15 MaintenanceChart.................

Téléchargements : 2   Taille : 8 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

NOTE: Strain and thin paint before using. All paint may have particles that will clog filter and spray tips. Remove any skin which may have developed on Operating Instructions and Assembly Instructions Airless Paint Sprayers the paint due to air exposure. Follow paint manufacturers’ recommendations on thinning paint. 12. When pure paint appears from spray tip rotate tip to the Spray position. The system is now ready for use. Clean Position 1 Spray Position 2 12” Holding Spray Gun Thin Coat Thin

Téléchargements : 0   Taille : 8 mb   Fabricant : Campbell Hausfeld  
Catégorie : Guns
@name

Part No. Description No. Q ty. R ef. Part No. Description No. Q ty. 10 Suction Bell (with filter) AL111000AJ 1 11a Suction Tube Assembly AL138400SV 1 11b Option, Solvent Resistant AL138404SV 1 12 Bucket Support (with screws) AL168080SV 1 13 Wheel, Pneumatic (optional) WA005620AV 2 14 Cap, Rubber (optional) MJ110300AV 2 15 Bucket Support (w/screws & nuts) AL167953SV 1 16 Stand AL168020AD 1 15 16 14 13 12 11 10 9 8 7 6 5 4 3 2 1 8 1 2 3 4 5 6 Operating Instructions and Assembly Instructions Troubl





catégories