Log:
Évaluations - 3, GPA: 4 ( )

Instructions iHome, Modèle IA17

Fabricant : iHome
Taille : 258.02 kb
Nom Fichier : iA17_English_IB.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


The battery backup circuit will also operate the buzzer alarm to wake you up at the selected wake up time even if the power is out. The battery backup circuit requires one CR2032 lithium battery, included. When the backup battery is getting weak the Low Backup Battery Indicator will begin flashing in the display. When you see this flashing indicator you should replace the backup battery as soon as possible. Purchase a replacement CR2032 battery, available wherever batteries are sold, and follow steps 1 through 4 below to install the replacement battery. To replace the backup battery: IMPORTANT: When replacing the backup battery be sure to have the unit connected to the AC outlet to maintain all of your settings, otherwise it will be necessary to reset the time, alarm time, and radio presets after the battery is replaced. 1. Locate the battery backup compartment found on the bottom of the unit. 2. Use a Phillips screwdriver to open the battery compartment cover. Remove the cover. 3. Insert a fresh CR2032 battery in the backup battery compartment with the “+” side facing up, as illustrated. 4. Replace the battery compartment cover and screw the compartment door back in place. Do not overtighten. Confirm that the backup battery indicator is not flashing in the display. Note: Make sure you dispose of battery properly (see your local regulations). WARNING: Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a pocket, purse, or other container containing metal objects, mix with used or other battery types, or store with hazardous or combustible materials. Store in cool, dry, ventilated area. Follow applicable laws Installing Backup Battery and regulations for transport and disposal. 3 Setting the Time Using Time Sync Setting the Time Using Time Sync The Time Sync feature allows you to sync the time setting on the unit to the time from your iPhone or recent model iPod (iPod touch, iPod nano and iPod Classic; older iPod models such as iPod mini do not support this feature). 1. Gently dock your iPhone or iPod. 2. Press and release the Time Sync Button on the back of the unit. The display turns orange and “SYNC” flashes in the display, indicating sync attempt. If sync is successful, the time will update and you will hear two beeps and the cabinet and display will turn green briefly. 3. If sync does not work, a long beep will sound and “FAIL” will appear in red on the display. If this happens, try using a different iPhone/iPod to attempt syncing again or set time manually (see below). NOTE: The iPhone is constantly updated to current time via cell phone towers. The time on your iPod is only accurate to the last time it was synced to a computer. It’s possible to have up to 59 seconds difference between the unit and synced iPhone/iPod. Setting the Time Manually 1. Set the DST Switch located on the back of the unit to +1 to add one hour for Daylight Saving Time or to -1 to subtract an hour for Standard Time. 2. Press and hold the Time Sync Button until the hour display flashes and turns orange. Press the + or – Button to set the correct hour (press and hold for rapid setting). Remember to set the correct AM or PM time. The PM Indicator is located to the upper left side of the time digits; there is no AM indicator. 3. Press the Button at any time during clock setting to toggle the display between 24 hour (military) and 12 hour (standard) display mode. The PM indicator will not appear when display is in 24 hour mode. 4. Press the Time Sync Button again (or no button press within 10 seconds) to exit the clock setting mode. The display and cabinet will flash green and 2 beeps will confirm clock setting is complete. Setting the Alarm 1. Press and hold the Button until the display turns orange and the alarm icon and alarm hour flashes on the display. 2. To set the desired alarm time, press the + or – Button (hold for rapid setting). Remember to set the correct AM or PM alarm time. The PM Indicator is located to the upper left side of the time digits; there is no AM indicator. 3. Press and release the Button. The current alarm source will flash. Press the + or – Button to cycle through alarm sources: iPod (includes docked iPhone or iPod), FM radio or buzzer (you cannot wake to aux audio device). 4. Press and release the Button to confirm wake to source. Unless radio was selected, you will go on to volume setting. • If radio is selected as the wake to source, the last wake-to FM station is displayed. Press and release the Presets Button to cycle through preset stations, or press the + or – Button to select a different station (hold briefly for rapid seek). Press and release the Button to confirm radio station setting and go on to volume setting. 5. The current alarm volume will appear on the display. Press the + or – Button to set the alarm volume from 05 -40. 6. Press the Button to confirm alarm volume. “colr” will appear...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories