Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
DS801-111 General 400-0442-006 3 SPECIAL APPLICATION MECHANICAL DS801-111 Housing 0.036” Aluminum Front Panel 0.035” Steel Length 4.10 in (104 mm) Width 1.38 in (35 mm) Height 1.20 in (30 mm) Weight 0.25 lb (0.11 kg) T° Operating 10°C-50°C T° Maximum 75°C Humidity 90% non-condensing MTBF (calc.) 38,000 hrs ELECTRICAL DS801-111 Input Video+ Stereo Audio Video/Sync/Audio Signals ALTINEX Standard Output Video Analog Signal 1.0 Vp-p max. Video Sync Level TTL Audio Level 0 dB +/-0.5 dB at 1 KHz Power Consumption External Adapter: 9 VDC 410 mA (3.7 W) max. Table 3. DS801-111 Electrical Table 2. DS801-111 Mechanical 400-0442-006 4 SPECIAL APPLICATION 400-0442-006 5 PRODUCT DESCRIPTION 4 4TP INPUT POWER VIDEO OUTPUT EQUALIZATION VIDEO AUDIO OUTPUT PRESENT LED POWER/SIGNAL SPECIAL APPLICATION 400-0442-006 6 APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUPS DS801-110 DS801-111 DA1930CT DS801-111 SPECIAL APPLICATION 400-0442-006 7 DIAGRAM 2: INTERNAL VIEW SEPARATOR PAIR 1 PAIR 3 PAIR 2 EQ H/W SEPARATOR PAIR 4 DETECT SIGNAL R/Pr G/Y B/Pb H V POWER LP LP RIGHT LEFT DS801-111 PS 4TP RJ-45 POWER 2-PIN TERM. BLOCK 9 V, 500 mA UNBAL. AUDIO STEREO 3.5mm COMPONENT VIDEO COMPUTER/ 15-PIN HD SYNC AUDIO SPECIAL APPLICATION INSTALLING YOUR DS801-111 6 OPERATION 7 Step 1. Determine the best location for the DS801-111. Where possible, locate the TP Transmitter as close to the video source as possible and the DS801-111 as close to the receiving component as feasible. Step 2. Apply power to the 2-pin terminal block on the rear of the DS801-111. The Power/Signal Present LED should be on and red. Step 3. Connect the receiving display to the output of the DS801-111 using a high-quality video cable. Step 4. Connect the audio amplifier or speakers to the audio jack on the DS801-111. Step 5. Run a UTP-type (CAT-5/CAT-5e) cable from the 4TP INPUT on the DS801-111 Receiver to the 4TP OUTPUT on the TP Transmitter. NOTE: Ensure good signal transmission by routing the cable to avoid any sharp angles, creases, or bends. Step 6. Connect the TP Transmitter per its installation instructions. In the case of the DS801-111, when the TP signal from the DS801-110 is applied, the Power/Signal Present LED will turn from red to green indicating a signal is present. Step 7. The units are now operational. The DS801-111 requires only one adjustment to be made for optimal performance. The adjustment is video equalization for long cable lengths. 7.1 VIDEO EQUALIZATION Video equalization is provided to fine-tune the displayed image on the remote display. Typically, for short cable runs the equalization will be set to near minimum. Start by setting the equalization to minimum on both units. Adjust the equalization on the receiver first. This adjustment should at least allow the receiving display to receive an image. Then use the equalization on both units to fine-tune the image for optimal quality. TROUBLESHOOTING GUIDE 8 We have carefully tested and have found no problems in the supplied DS801-111. However, we would like to offer suggestions for the following: 8.1 NO DISPLAY Cause 1: The source has a problem. Solution: Check the source and make sure there is a signal present and all source connections are correct. If the source is working and there is still no display, see Cause 2. Cause 2: The path has a problem. Solution: Connect the transmitter directly to the receiver using a short UTP patch cable. If the image is good, there is a problem with the cable. Otherwise, see Cause 3. Cause 3: Cable connections are incorrect. Solution: Make sure that cables are properly connected. Also, make sure that the continuity and wiring are good. If there is still no display present, see Cause 4. 400-0442-006 8 SPECIAL APPLICATION Cause 4: Video equalization required. Solution: Adjust the VIDEO EQUALIZATION on the DS801-111. Some monitors are very sensitive to signal quality and this may prevent the monitor from displaying an image until the equalization is adjusted. See the operation section for adjustment details. Cause 5: The display has a problem. Solution: Make sure the display is powered and is turned on. If there is still no display, please call ALTINEX at (714) 990-2300. 8.2 NO SOUND Cause 1: The source has a problem. Solution: Check the source and make sure that there is a signal present and all source connections are correct. If the source is working and there is still no sound, see Cause 2. Cause 2: The volume is too low. Solution: Increase the gain at the source. If there is still no sound present, see Cause 3. Cause 3: Cable connections are incorrect. Solution: Make sure that cables are properly connected. Also, make sure that the continuity and wiring are good. If there is still no sound, see Cause 4. Cause 4: The receiving device has a problem. Solution: Make sure the receiving device is powered and is turned on. If there is still no sound, please call ALTINEX at (714) 990-2300. ALTINEX POLICIES 9 9.1 LIMITED WARRANTY/RETURN POLICIES Please see the ALTINEX webs...