Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
The input termination is switch selectable to either be 600 Ohms or high impedance. The DAV0106-V1A2 Distribution Amplifier will allow the connection of video and audio amplifiers simultaneously. The DAV0106-V1A2 Distribution Amplifier is a state-of-the-art product with a bandwidth of 130MHz for video signals, which enables it to remain transparent to the incoming video signals passing through it. It also has a bandwidth of 10Hz to 20kHz for audio signals. The DAV0106-V1A2 can pass NTSC, PAL or SECAM type video signals. The DAV0106-V1A2 can drive output signals up to 75 feet or more when it is used with high-quality coaxial cables. The DAV0106-V1A2 receives power from a universal power supply and accepts input from 95 to 240 Volts AC at 50 or 60 Hz. TECHNICAL SPECIFICATIONS 3 FEATURES/ DESCRIPTION Video Audio Compatibility NTSC, PAL, SECAM, Composite Video Stereo or Mono Audio No of Inputs 1 1 Input Connector One BNC Female One 3.5 mm 5-pin Terminal Block Input Signals Level 1.7V 10 V p-p max Impedance 75 Ohms or unterminated 600 Ohms or high impedance Type Differential input isolated from GND Differential input isolated from GND No of Outputs 6, +1 input loop 6 Output Connector Seven BNC Female Six 3.5mm Terminal Blocks Output Signals Level 3V p-p max 10V p-p Impedance 75 Ohms Low - drives 600 Ohms Type Outputs isolated from GND Differential input isolated from GND Gain 0d B 0d B unbalanced, +6d B balanced Differential Gain/Phase less than 0.02% @ 20 IRE, 0.01° @ 20 IRE __ Frequency Compatibility Typical Bandwidth 85 MHz @ -3d B 10 Hz – 20 kHz Flatness 0.1d B to 30 MHz __ 3 DISTRIBUTION AMPLIFIERS Power Internal Power Supply 90-140V/ 200-240V Power Consumption 10 watts max Enclosure Material 0.1” Al Finish Gray Top panel Lexan Height (inches) 1.75in (44mm) Width (inches) 8.50in (216mm) Depth (inches) 4.93in (125mm) Weight 2.0lbs. (0.91kg) Ship Weight 4.0lbs. (1.81kg) T° Operating 10°C-35°C T° Maximum 50°C Humidity 50% non-condensing MTBF (calculations) 40,000 hrs DESCRIPTION OF DAV0106-V1A2 4 4 DISTRIBUTION AMPLIFIERS APPLICATION DIAGRAM 5 5 DISTRIBUTION AMPLIFIERS INSTALLING YOUR DISTRIBUTION AMPLIFIER 6 OPERATION 7 Step 1. Connect the power cord to the unit and plug it into the power outlet. The power indicator LED on the front panel will light. This indicates that the unit is operational. Step 2. Connect the video/audio output of the source (TV, VCR, etc.) to the input of the DAV0106-V1A2 using high quality cables. The active signal indicator on the back panel will light. This indicates an input signal on the input of the distribution amplifier. Step 3. Connect the output channels of the amplifier to the display devices, such as monitors or projectors. Step 4. Verify that the quality of output signals on all displays or speakers is good. If the quality of the output signal is less than perfect, make sure that all connections are solid and high quality cables are used. CONGRATULATIONS! YOU ARE DONE. If you experience any problems, please call 1-800-258-4623 or 1-714-990-2300 for international calls. The DAV0106-V1A2 will operate successfully as long as cables are attached properly and other technical specifications are met. 7.1 TERMINATION SWITCH The termination switch of the video amplifier, when set to the ON position, will provide 75 Ohms of termination to the input. If the termination switch is in the OFF position, the input will be unterminated. Use the OFF position when using the Video Loop to pass the Video input to a local display, for instance. This switch does not affect the termination of any output signal. The termination switch of the audio amplifier may be set to 600 Ohms on the audio input if it is in the ON position, and high impedance in the OFF position. 6 DISTRIBUTION AMPLIFIERS ACCESSORIES 8 Model No. Description TABLE MOUNT BRACKETS TM1271 1 U High, . Rack-Wide 1 U High, . Rack-Wide with 15-pin HD connector plate TM1272 1 U High, . Rack-Wide with SNAPIN connectors TM1273 1 U High, . Rack-Wide with SNAPIN and power connectors TM1274 RACK MOUNTING BRACKETS DA1293FC 19” - 1U Rack Mount Shelf (for tandem 2- Units) 19”- 1U Rack Mount Ears for single unit DA1294FC HIGH RESOLUTION MULTICHANNEL COAX CABLE length XX = 3, 6, 12, 25, 50, 75, 100, 150 feet 4 BNC to 4 BNC CB41XXMR 5 BNC to 5 BNC CB42XXMR SUPER HIGH RESOLUTION MULTI-CHANNEL COAX CABLE length XX = 3, 6, 12, 25, 50, 75, 100, 150 feet 4 BNC to 4 BNC CB43XXMR 5 BNC to 5 BNC CB44XXMR PLENUM-FLEX MULTI-CHANNEL COAX CABLE length XXX = 3, 6, 12, 25, 50, 75, 100, 150, 200, 250 feet 5 BNC to 5 BNC, high resolution CB5000PL coax cable 5BM0XXX5BM 5 BNC to 5 BNC, super high CB5100PL resolution coax cable 5BM0XXX5BM POWER CABLES PC5301US Power cable for US Power cable for England PS5302UK Power cable for Australia PS5303AU Power cable for Germany PS5304GR FREQUENTLY ASKED QUESTIONS 9 No: Question Answer 1 What is a distribution amplifier? A distribution amplifier is a device that allows you to connect a single signal source to multiple display ...