Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
The following pages list the parameters from the menu tabs available in the DashBoard software when connected to a 9034. Description Card Info (Read-only) Product CDI-9034 The product name Manufacturer Cobalt Digital Inc. The manufacturer of the product Software Release Number ### The release number of the firmware in this card Software Build Date ### The internal build number of this software Software Build Time ### The date and time the software was created +12 V Power Rail #.## W Positive Supply Power -7.5 Power Rail #.## W Negative Supply Power Video Input Standard ############ Detected Video Standard on SDI or Analog Input Reference Standard ############ Detected standard of selected reference. SSN ############ Displays the Silicon Serial Number of the card. 9034 Owner’s Manual • •••• (V 2.0) Page 19 of 28 Description Frame Sync Framesync Enable On/Off Enables the Frame Sync Horizontal Offset 0-4125 samples Applies additional horizontal offset Vertical Offset 0-1124 lines Applies additional vertical offset Minimum Latency Lines 3-1124 lines Selects the minimum lines of latency allowed. Minimum Latency Fields 0-27 Selects the minimum fields of latency allowed. Framesync Status On/Off/Error Shows the status of the FS Reset Framesync Confirm Resets the FS and its buffers. Re-establishes audio video sync after a adjusting the horizontal and vertical offsets. Description AES Audio Out 1/2 -7/8 Source (per channel) AES 1-16 Selects the source for the AES outputs. Each AES source can be chosen separately. Analog 1-8 Silence Gain (per channel) Range (-400) -400 Gain applied to AES audio output. Phase (per channel) Normal Inverts the phase of the AES audio output. Invert Description Tone Generator Tone Generator 1-4 Frequency Range 50Hz –16KHz Selects the frequency of the tone generated. Description Presets Parameter Save Confirm Saves the parameters as preset. Parameter Load Confirm Loads parameters previously saved. Restart Parameters to Factory Default Confirm Will load factory presets and overwrite the save. Page 20 of 28 9034 Owner’s Manual • •••• (V 2.0) Description Video Signal Controls SD Input Type Composite Selects the format of input SD analog video, so the decoder can properly decode the signal. Y/C YPbPr BetaCam YPbPr MII YPbPr SMPTE HD Input Type GBR Selects the format of input HD analog video. YPbPr SD Composite Contains 0.0 or 7.5 IRE of Setup Specifies the amount of setup (pedestal) in the input video. It will be removed by the decoder. Description AES Input Controls AES Pair 1-8 SRC Bypass On This will bypass sample rate conversion on AES. If bypassed AES rate must match input video rate or audio dropout will occur. SRC must be bypassed to embed Dolby encoded audio. Off AES Pair 1-8 Passthrough On AES output pair X will be a low latency copy of AES input pair X.Off AES Pair 1-8 Zero Delay On Embeds with low (<1 ms) latency. Overrides routing choices.Off Description Video Proc Video Gain Range 0-2000 Gain applied to Y (Luma). 1000 is unity. Video Lift Range (-999) – 999 Lift applied to Y (Luma), in 10 bit code value. Color Gain Range 0-2000 Gain applied to C (Chroma). 1000 is unity. Color Phase Range (–360) – 360 Phase of C (Chroma) in degrees. Reset to Unity Confirm Resets all of the proc controls to unity. 9034 Owner’s Manual • •••• (V 2.0) Page 21 of 28 Technical Specifications Table 4. Card -Technical Specifications Analog Video Input Number of Inputs 3 Input Type Differential, Common Mode Rejection (5V AC) Video Inputs HD: Component YPbPr and RGB SD: Composite, Component YPbPr (BetaCam™, MII™, SMPTE/N10), RGB, and Y/C Conversion Bit Depth 12-Bits SD Color Separation 5-Line Adaptive Comb or Notch Filter Frequency Response HD: Y-0-30MHz ± 0.25db PbPr 0-15 MHz ± SD: Y-0-30MHz ± 0.25db PbPr 0-15 MHz ± Differential Phase SD: < ±0.4° typical Differential Gain SD: < ±0.4% typical Noise < -64dB (Luma Flat Field) < -61dB (Luma Ramp) Analog Front End Crosstalk Within Noise Floor Measurement Return Loss > 20dB to 30MHz Specification Serial Digital Video Outputs Number of Outputs 2:HD/SD-SDI BNC per IEC 60169-8 Amendment 2 Impedance 75. Return Loss > 15 dB at 5MHz – 270MHz > 12 dB at 270MHz – 1.485GHz Signal Level 800 mV ±10% DC Offset 0 Volts ±50 mV Jitter HD: < 0.15UI (all outputs) SD: <0.06UI (all outputs) Overshoot <0.2% of amplitude Page 22 of 28 9034 Owner’s Manual • •••• (V 2.0) AES Audio Input Standard SMPTE 276M Number of Inputs 8 unbalanced Input Level 0.1 to 2.5V p-p (5V p-p tolerant) Input Impedance 75. Return Loss > 12dB 100kHz to 6MHz Equalization Automatic to 1000m with Belden 1694A (or equivalent) @ 48kHz AES signal Sample Rate 48KHz AES Audio Output Standard SMPTE 276M Number of Outputs 8 unbalanced Output Impedance 75. Return Loss > 30dB 100kHz to 6MHz Resolution Up to 24-bit Sample Rate 48KHz Analog Audio Input Number of Inputs 4 Balanced Analog Audio Connector Phoenix 3-pin Sampling Rate 48KHz (free run or locked to the reference) Signal Level +24dBu => 0dBFS Specification Referenc...