Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Shrink Aspect (4:3 Monitor) The source aspect ratio will be maintained and the picture will shrink into full view on the screen. Sidebar Aspect (16:9 Monitor) 4:3 pictures will be viewed on a wide aspect "IV screen with vertical bars on both sides of the picture. Expand Aspect (16:9 Monitor) 4:3 pictures will be viewed on a wide aspect TV screen with the picture digitally "stretched" to fill the screen. Note: See following page for illustrations of the various aspect ratios. [] Source Signal 16 4 T The 16:9 and 4:3 pictures represent the incoming source signals received by the STB. ASPECT RATIO FORMATS ZOOM SIDEBAR EXPAND FULL ZOOM LETFERBOX SHRINK T These pictures show the different aspect ratios These pictures show the different aspect ratios available with a 16:9 monitor format. available with a 4:3 monitor format. The top picture shows the 16:g monitor The top pictures show the 4:3 monitor format available when the STB receives a formats available when the STB receives a 16:9 source signal. 16:9 source signal. The bottom pictures show the 16:9 monitor The bottom picture shows the 4:3 monitor formats available when the STB receives a format available when the STB receives a 4:3 source signal. 4:3 source signal. B SPECIAL REMOTE BUTTONS TV/VIOEO TV/Video C) The W/VIDEO button allows you to select the mode of your TV. Each time the TV/ VIDEO button is pressed, the TV will cycle through Channel, Video 1, Video 2, Video 3 and D'iV modes. Note: Not all television models will display all the modes. Menu MENU O The MENU button allows you to access and exit the Roller Guide Menu. Each time the MENU button is pressed, the Roller Guide will appear on and disappear from the viewing screen. Next Program PROG O The PROG button allows you to select programs within a single 6 MHz channel. Each time the PROG button is pressed, the STB will move to the next available program within the channel. Note: Only programs within the current 6 MHz channel can be selected using the PROG button. If only one (1) program appears, it indicates only one (1) program is available, R-TUNE Rapid Tuning O The R-TUNE button quickly switches between two channels or programs. The STB will attempt to immediately tune to the last channel or program in its memory. If programs are no longer transmitting on the channel, the Unavailable Channel Screen will display and the STB will automatically select the first program available on the channel. Recall RECALL The RECALL button displays the Recall Screen for 6 seconds or until you press any button (which automatically exits the Recall mode). [] PROGRAMMING THE REMOTE CONTROl Programming the Remote Control The Universal Remote Control can be programmed to operate many manufacturers' components using the component function buttons for VCR, DVD, AUX (RCVR, CD, TAPE, CASSETTE DECK and LD), CBL, D'I-V, TV, or DBS. Follow the procedures for programming your Remote Control with and without codes for the component. Determine the manufacturer of the component and look in the table for the code. Note: Be carefulto press ACTION inthemiddleofthebutton,ff you do not press in the middle of the button, the arrow buttonsmay be activated. This will interruptyour programming. Programming With Code • Confirm that the external component is plugged in and is turned on. • Turn the component off. • Press the ACTION and POWER button, together, for at least 5 seconds. All mode buttons will flash, then let go of the buttons. • Press appropriate component button (VCR, CBL, etc.) on the Remote Control. The pressed button will illuminate steadily. All other buttons will go out. • Enter the 3-digit component code using the Remote Control numeric keypad (0 ~ 9 buttons). If a proper code was entered, the mode button will blinktwice and go out. • Press the Remote Control POWER button to test the component. If the procedure was successful, the component will turn on. If the component does not operate with the Remote Control, repeat the procedure using another code. (Some brands have multiple codes.) If an incorrect code is entered, or ff the procedure takes longer than 30 seconds, the programming will fail. Programming Without Code This procedure searches all codes and is called the "sequence method". • Confirm that the external component is plugged in and is turned on. • Turn the component off. * Press the ACTION and POWER button, together, for at least 5 seconds. All mode buttons will flash, then let go of the button. • Press appropriate component button on the Remote Control. The pressed button will illuminate. All other buttonswill go out. • Press the D, button to move forward to the next code. Press the <1 button to move backward. • Press the Remote Control POWER button to test the component. If the procedure was successful,the component willturn on. Note: Repeat the preceding two steps until the component code is found. It may take many attempts before the correct code is found. • After the code is found, press the ACTION button...