Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Channel Plus, Modèle CHANNEL PLUS 5115BID

Fabricant : Channel Plus
Taille : 176.32 kb
Nom Fichier : 451536f8-d9f7-4ddf-a349-df313ec0a364.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter © 1999 Out Incoming CATV or to TVs antenna coax Installation Step Two The wall plate Run a line of Cat and connect wires note: When using quad wire connect wires only to pins 1, 2, 5 and 6. Leave the resistor in place at pins 3 and 4. At the channel injector, connect Cat 5 wire as shown. Follow the color coding on the screw terminal. Bl/W Blue Org/W Orange Gr/W Green Br/W Brown Green Red Black Yellow pin 1 2 3 4 5 6 7 8 Default resistor pin 1 2 5 6 note: When using Cat 5 wire remove the default resistor that is in pins 3 and 4 of the wall plate screw terminal Side view of wall plate blue/white pin 1 © 1999 When using only quad wire use positions 1, 2, 5 and 6 and follow color coding. blue/white run the Cat 5 wire pin 1 through the grommet at the bottom of the injector Connecting Source Using any video plate as shown. wire to the channel * Optional loop © 1999 Audio/video connections Cat 5 wire Coax jumper Out to TVs out television or a/v receiver Antenna or CATV feed Video source * Use the NORM / LOOP switch to select the proper setting application. Norm/Loop switch NORM: Select NORM when a television or a/v receiver is not used at the wall plate to view the connected source. LOOP: Select LOOP when a television or a/v receiver is connected to the wall plate to view the connected source Applying Step Three The 5115 series to the system. Use only one method Method One: Apply power directly to power supply. Power plug Lower right of channel injector © 1999 power supply The green LED in the upper right corner of the injector will be lit showing power is active. (See power length requirements page 8) Method Use the power injector to apply power 5 or quad wire the power injector. Connect the plug the power supply power injector pin 1 blue/white cut Cat 5 wire power plug power supply The green LED in the upper right corner of the channel injector will be lit showing power is active. Method Three: Apply power directly at the wall plate. The green LED in the lower right corner of the wall plate and upper right corner of the channel injector will be lit showing power is active. power plug Power Length Method One Up to 300’ of Cat 5 or quad wire maximum power plug Power Length Requirements Method Two power plug Up to 300’ of Cat 5 or quad wire maximum Up to 100’ of Cat 5 or quad wire maximum Power Length Requirements Method Three Up to 100’ of power plug Cat 5 or quad wire maximum How to Determine which source on and one unused channel avoid interference. channels and appear Upper right corner onchannel injector green LED © 1999 programming button To program: For example channel 60 1: Press the button 6 times. 2: Wait for the LED to relight. 3: Press the button 10 more times (pressing 10 times enters “0”)...

Ce manuel est également adapté pour les modèles :
Récepteur et amplificateur - CHANNEL PLUS 5115HHR (176.32 kb)
Récepteur et amplificateur - CHANNEL PLUS 5115PAL (176.32 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories