Log:
Évaluations - 3, GPA: 3.3 ( )

Instructions Adcom, Modèle Alpha 8P

Fabricant : Adcom
Taille : 1.07 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


You also need to make a connection from the preamp out sockets of your integrated amplifier, or preamplifier, to the power amp in sockets of the power amp. ADDING AN ALPHA 8P TO AN EXISTING ALPHA 7 OR 8 INTEGRATED AMPLIFIER If you are using an Alpha 7 or 8 amplifier, an Alpha 8P can be added to bi-amplify a pair of biwireable loudspeakers. This will reap substantial improvements in sound quality if the following advice is observed. ■ Always switch on the integrated amplifier and allow it to stabilise (indicator light turns green) before switching on the Alpha 8P. ■ The integrated amplifier and Alpha 8P power amplifier are placed on separate shelves. BI-AMPING YOUR LOUDSPEAKERS INTEGRATED AMPLIFIER R L + = + POWER AMPLIFIER ENGLISH (Stacking the units on top of each other will reduce the sound quality slightly. It will also reduce ventilation and consequently the continuous power handling capability). ■ The existing integrated amplifier should be used to drive the loudspeakers' HF (high frequency or treble) units. The new Alpha 8P is utilised for the LF (low frequency or bass) drivers, as shown in the wiring diagram below. ■ At the end of a listening session the Alpha 8P should always be turned off first. ■ High quality interconnect cables should be used between the integrated amplifier and Alpha 8P. ■ The use of high quality interconnect and speaker cables in your system is essential to obtain good sound quality. Contact your dealer for further details. Note: The second set of speaker terminals (SP2) on both units can be used to drive extra loudspeakers in other rooms provided the impedance of these is 8 ohms or more. ■ WARNING - Ensure that the TERMINAL LINKS ARE REMOVED from your biwireable loudspeakers before switching on the amplifiers. Failure to do this could cause damage to one or both amplifiers and this is not covered under the warranty. SAFETY STANDARD ■ These products have been designed to meet the IEC 65 international electrical safety standard. Guarantee Information ENGLISH GUARANTEE FOR UK SALES This equipment is guaranteed for two years from the date of purchase (parts and labour only), provided that it was originally purchased from an authorised dealer under a consumer sale agreement. (The words "consumer sale" shall be construed in accordance with Section 15 of the Supply Of Goods [Implied Terms] Act 1973). The manufacturer can accept no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or through unauthorised adjustment and/or repair, neither can they accept responsibility for damage or loss occurring during transit to or from the person claiming under this guarantee. This guarantee is applicable within the UK only. It is transferable to subsequent purchasers, but the liability of the manufacturer is limited to the cost of repair of the defective parts and under no circumstances extends to consequential loss or damage. Claims under this guarantee This equipment should be packed in the original packing and returned to the dealer from whom it was purchased, or failing this, directly to Arcam. It should be sent carriage prepaid by a reputable carrier - NOT by post. No responsiblity can be accepted for the unit whilst in transit to the factory, or an agent, and customers are therefore advised to insure the unit against loss or damage whilst in transit. If the original packing is not available, replacement packing can be purchased from Arcam. DO NOT CONSIGN THE EQUIPMENT TO ARCAM UNLESS YOU HAVE BEEN SPECIFICALLY REQUESTED TO DO SO BY THE CUSTOMER SERVICE DEPARTMENT. DO NOT UNDER ANY CIRCUMSTANCES ATTEMPT TO DISASSEMBLE THE EQUIPMENT BEFORE DESPATCH. You can contact the manufacturer at the following address: ARCAM Customer Service Department, Pembroke Avenue, Denny Industrial Centre, Waterbeach, Cambridge, CB5 9PB, England. Telephone: +44 (0)1223 203203 Fax: +44 (0)1223 863384 e-mail custserv@arcam.co.uk You should state clearly your name and address, the date and place of purchase together with a brief description of the fault. In the event of equipment being returned which, after having been tested, is found to comply with the published specification, the manufacturer reserves the right to charge a reasonable fee for testing the equipment and for the return carriage. THIS GUARANTEE IN NO WAY VARIES OR REMOVES A PURCHASER’S STATUTORY RIGHTS. GUARANTEE FOR SALES IN THE EUROPEAN ECONOMIC COMMUNITY (EEC) This unit is covered by a European Economic Community warranty. This entitles you to have the unit repaired free of charge, during the first year after purchase, at any authorised Arcam distributor within the EEC, provided that it was purchased from an authorised ARCAM dealer or distributor within tty EEC. The manufacturer can accept no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or through unauthorised adjustment and/or repair, neither can they accept responsibility for...

Ce manuel est également adapté pour les modèles :
Récepteur et amplificateur - Alpha 8 (1.07 mb)
Récepteur et amplificateur - Alpha 8 (1.07 mb)
Récepteur et amplificateur - Alpha 8P (1.07 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories