Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Install wire antennas high enough that they will not be "walked into" by people. Do not install antenna wire(s) over or under utility lines. ENIncluded with Antenna N o t e : For final installation and connection of your antenna, a dd i- tional hardw are may be re q u i re d . B e fo re starting assembly, p l e a s e read through the instructions care- f u l ly to determine your specific re q u i re m e n t s . P a rts included: a. UHF Boom-A . . . . . . . . . . . . . . . . . 2 b. UHF Boom-B . . . . . . . . . . . . . . . . . 2 c. VHF Boom-A . . . . . . . . . . . . . . . . . 1 d. VHF Boom-B . . . . . . . . . . . . . . . . . 2 e. Reflector Elements . . . . . . . . . . . . . 2 f. 46. Element . . . . . . . . . . . . . . . . . . 2 g. 50. Element . . . . . . . . . . . . . . . . . . 2 h. Tubing Brace . . . . . . . . . . . . . . . . . . 2 j. Phasing Wire . . . . . . . . . . . . . . . . . . 2 k. Reflector Brackets . . . . . . . . . . . . . 2 l. Pivot Brackets . . . . . . . . . . . . . . . 4 n. Locking Brackets . . . . . . . . . . . . . . . 4 p. End Caps . . . . . . . . . . . . . . . . . . . . . 8 q. Screws (1-3/4.) . . . . . . . . . . . . . . . . 5 r. Screws (1-1/2.) . . . . . . . . . . . . . . . 10 s. Screws (3/4.) . . . . . . . . . . . . . . . . . 2 t. Lock Washers/ Washers . . . . . . . 6, 4 u. Wing-Nuts . . . . . . . . . . . . . . . . . . 17 v. Nuts . . . . . . . . . . . . . . . . . . . . . . . . 6 w. Band Separator . . . . . . . . . . . . . . . . 1 x. U-Bolt . . . . . . . . . . . . . . . . . . . . . . . 3 y. Cross Piece (for U-Bolt Assembly) 3 z. Antenna Saddle . . . . . . . . . . . . . . . . 1 *Quantities listed include those which may already be attached to antenna NOTE: Cable, mast and mounting brackets are not included. Assembly Assembly of UHF Portion • Rotate reflector element rods into place. NOTE: When rotating element rods, grasp close to pivot and relieve spring pressure on pivot bracket detents. Don’t apply excess pressure to reflector element rods. 5 EN Assembly • Insert UHF Boom-A into UHF Boom-B and secure using 1-1/2. screw and lock washer. • Attach Reflector Arm Mounting Brackets to assembled UHF Boom (previous step) using two 1-1/2. screws and wing-nuts. Ensure that rotation arcs in Reflector Arm Mounting Brackets face toward UHF Boom elements. • Attach Corner Reflector Arms to Reflector Arm Mounting Brackets by sliding Reflector Arms between Mounting Brackets. Secure with 1-1/2. screw and wing-nuts. To fully secure Reflector Arms, snap into locking tabs and tighten screws. Assembly of VHF Portion • Rotate reflector element rods on VHF Boom-A and VHF Boom-B into place. NOTE: When rotating element rods, grasp close to pivot and relieve spring pressure on pivot bracket detents. Don’t apply excess pressure to reflector element rods. • Attach one 46. Element to hole A in VHF Boom-B. • Attach one 50. Element to VHF Boom-B. Repeat each steps with second boom for VHF Boom-B. ENAssembly • Insert VHF Boom-B into VHF Boom-A and secure using 1-1/2. screw and lock washers. Repeat steps for 2nd boom as well. • Attach tubing brace to rear of VHF Boom with 1-1/2. screws and wing-nuts. • Slide UHF Boom through center slot of VHF Boom support block until hole A of UHF Boom aligns with hole B of VHF Boom. Secure with 1-1/2. screw and wing-nut. • Attach phasing wire and lead-in wire to UHF antenna using 3/4. screws, washers, and wing-nuts. • Insert end caps at ends of all booms. Mast Assembly (Mast not included) • Assemble U-bolts to cross pieces. • Use saddle on center of boom. • Assemble U-bolt assemblies loosely to antenna. • Insert mast through U-bolts. • Tighten U-bolts securely. All U-bolts should be on one side of mast. • Attach mast standoff to mast. • Insert wire in standoff and tighten with pliers. • Power lines should be as far away as possible. • Assemble U-bolts in wall mounts with lock washers and nuts. • Secure mounts to wall with wood screws. • Separate mounts by at least two feet. • Insert mast with assembled antenna through both U-bolts. • Face antenna toward TV station. • Tighten U-bolts securely. • Wall mounts and chimney mounts are not included. 7 EN Assembly Lead-In Wire • Attach lead-in wire to house with screw-type standoffs. • Tighten standoffs with pliers after wire is installed. • Avoid sharp bends in lead-in wire. • Form drip loop where wire enters wall. • Wall mounts not included. • Mounts, mast and standoffs are not included. Band Separator • Attach band separator to appropriate terminals on TV set. • Attach antenna lead-in wire to band separator. • An FM set or second TV set may be attached to second output of band separator. NOTE: Band separator is only required for older TV sets with separate VHF/UHF inputs. For most newer sets, simply connect cable from antenna to ‘F’ input. SPWarranty Limited Lifetime Warranty The manufacturer warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specifications and w...