Fabricant : Pioneer Taille : 12.41 mb Nom Fichier : Langue d'enseignement:

Aller à la télécharger

R L FRONT OUTPUT R L SURROUND OUTPUT CENTER OUTPUT SUBWOOFER OUTPUT R L SURROUND BACK OUTPUT VIDEO OUT VIDEO ! If there is a single surround back output, connect it to the SURR BACK L jack on this receiver. ! To use a 5.1-channel speaker set, use the surround speakers for the surround channel, not the surround back channel. ! The sound from the surround back terminals will depend on how you have configured the Speaker system setting on page 87. ! The audio signal input to MULTI CH IN cannot be downmixed. Connecting additional amplifiers This receiver has more than enough power for any home use, but it’s possible to add additional amplifiers to every channel of your system using the pre-outs. Make the connections shown below to add amplifiers to power your speakers. IN ONO GND SIGNAL CD IN OUT 1 (CONTROL) OUT 2 PRE OUT MULTI CH IN FRONT 1 SUBWOOFER 2 CENTER SURROUND SURR BACK F HEIGHT F WIDE L R FRONT CENTER SURROUND SURR BACK (DVD) (CD) COAXIAL ASSIGNABLE IN 1 IN 2 (TV/SAT) (DVR/BDR) OPTICAL ASSIGNABLE IN1 IN2 IN3 OUT (VIDEO) (OUTPUT 5 V 0.1 A MAX) DC OUTPUT ADAPTER PORT for WIRELESS LAN (10/100) LAN (OUTPUT 5 V 0.6 A MAX) NTER SURROUND SURROUND BACK R L R L R L R L (Single) (Single) FRONT HEIGHT FRONT WIDE / B A AC IN VIDEO AUDIO NITOR UT R) SUBWOOFER R L ANALOG INPUT R L ANALOG INPUT R L ANALOG INPUT ANALOG INPUT ANALOG INPUT R L ANALOG INPUT Front channel amplifier Center channel amplifier (mono) Surround channel amplifier Front height channel amplifier R L ANALOG INPUT Front wide channel amplifier Surround back channel amplifier Powered subwoofer 1 ANALOG INPUT Powered subwoofer 2 ! If you’re not using a subwoofer, change the front speaker setting (see Speaker Setting on page 85) to LARGE. ! You can use the additional amplifier on the surround back channel pre-outs for a single speaker as well. In this case plug the amplifier into the left (SURROUND BACK L (Single)) terminal only. ! The sound from the surround back terminals will depend on how you have configured the Speaker system setting on page 87. ! If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal. Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this case, the same sound is output from the two subwoofers. ! To hear sound only from the pre-outs, switch the speaker system to OFF, or simply disconnect any speakers that are connected directly to the receiver. En 29 Connecting your equipment 03 Connecting AM/FM antennas Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Connecting external antennas on page 29). AM LOOP FM UNBAL 75 ANTENNA 3 1 4 a b c 5 2 1 Pull off the protective shields of both AM antenna wires. 2 Push open the tabs, then insert one wire fully into each terminal, then release the tabs to secure the AM antenna wires. 3 Fix the AM loop antenna to the attached stand. To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. a) then clip the loop onto the stand (fig. b). ! If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. c) before clipping the loop to the stand. Make sure the reception is clear. 4 Place the AM antenna on a flat surface and in a direction giving the best reception. 5 Connect the FM wire antenna into the FM antenna socket. For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up. Connecting external antennas To improve FM reception, connect an external FM antenna to FM UNBAL 75 W. AM LOOP FM UNBAL 75 ANTENNA 75 coaxial cable To improve AM reception, connect a 5 m to 6 m length of vinyl-coated wire to the AM LOOP terminals without disconnecting the supplied AM loop antenna. For the best possible reception, suspend horizontally outdoors. AM LOOP FM UNBAL 75 ANTENNA Outdoor antenna Indoor antenna (vinyl-coated wire) 5 m to 6 m MULTI-ZONE setup This receiver can power up to three independent systems in separate rooms after you have made the proper MULTI-ZONE connections. Different sources can be playing in three zones at the same time or, depending on your needs, the same source can also be used. The main and sub zones have independent power (the main zone power can be off while one (or both) of the sub zones is on) and the sub zones can be controlled by the remote or front panel controls. Making MULTI-ZONE connections It is possible to make these connections if you have a separate TV and speakers for your primary (ZONE 2) sub zone, and a separate TV and a separate amplifier (and speakers) for your secondary (ZONE 3) sub zone. You will also need a separate amplifier if you are not using the MULTI-ZONE setup using speaker terminals (ZONE 2) on page 29 for your primary sub zone. There are two primary sub zone setups possible with this system. Choose whichever works best for you. MULTI-ZONE listening options The foll...

Ce manuel est également adapté pour les modèles :
Récepteur et amplificateur - SC-LX85 (12.41 mb)

Téléchargez votre

Pour télécharger, entrez 2 chiffres :