The emitter housing can be removed for internal placement within components, if desired, for custom installations. The AIE1 produces high-output IR signals from the upper, curved surface while low-output IR signals eminate from the flat, lower surface. Use the high-output side to mount an emitter to a nearby surface such as a cabinet, shelf, or door to “blast” IR to several components at once. Use the low-output side to place directly over a component’s IR receiver. High-OutputLow-OutputConnecting LeadEmitterHousingInternalIR Emitter1 Installation • Locate the component’s IR receiver window. Thoroughly clean this window to remove fingerprints, dust, etc. • Peel the protective layer off of the adhesive strip on the docking station and apply to the IR receiver window. • Orient the docking station vertically, then press down for several seconds to ensure good contact with the adhesive. • Slide the emitter down from the top into the docking station. It should snap into place. • Connect the 3.5mm plug into an ATON DLA 2/4/6 Speaker Selector, AIB4 Amplified IR Connection Block or other source of IR. • Remove the emitter from the docking station by sliding it upward. Attach Docking Station to IR Receiver Window w/Adhesive Strip Slide Emitter into Docking Station Emitter Properly Installed Installation Notes: • Read the Owner’s Manual for the component to be controlled to find where the IR receiver window is located. A flashlight can also be useful for this purpose. • Emitters can be attached without the docking station. Use an extra adhesive strip (included) applied directly to the flat side of the emitter. • Use a new adhesive strip when re-attaching docking ports or emitters. • The outer shell of the AIE1 is transparent to IR so that hand-held remotes can be used even if the emitter is covering the component’s IR receiver. 2 Typical Installation To 120V AC (unswitched) PS2 Power Supply Digital Music Server Satellite DVD AIE1 IR Emitter Remote Control AIE1 IR Emitter AIE1 IR Emitter AIB4 Amplified IR Connection Block AIR1 Plasma Friendly Surface-Mount IR Receiver Caution: Do not plug the AIE1 into an emitter jack that is set to HIGH Power or “Blaster” as this will damage the emitter. Additional Locations for Emitter Placement Since the AIE1 has high output from its curved surface, it may be attached to nearby surfaces such as shelves, doors, or cabinets. Use the LOW power setting (not blaster power) on the connection block. Shelf Cabinet Door 3 Limited Warranty ATON* warrants to the purchaser/end user (“you”) that the AIE1 is to be free from defects in materials and workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is transferable to subsequent owners of the product as long as the original proof of purchase is retained. If you discover a defect in material or workmanship within the Warranty Period, you can obtain warranty service by contacting ATON during the Warranty Period at (859)-422-7137 or service@atonhome.com. If ATON determines that the product is in fact defective, ATON shall, at its option, repair or replace the product free of charge to you. This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was improperly installed, (c) which was repaired or altered by persons other than ATON or its authorized representatives or subject to unauthorized tampering, alteration or modification, (d) damaged due to misuse, negligence, accident, acts of God (including, but not limited to, excess moisture, insects, lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events beyond ATON’s control), or (e) subject to improper operation, maintenance or storage or unreasonable use. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. The foregoing remedies shall be your exclusive remedies for any breach of warranty. Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third Party Products”). With respect to any Third Party Products, the warranty for such product shall be as provided by the manufacturer of such product, who will also be responsible for warranty service, and ATON will pass through to you any transferable warranty actually extended to ATON by the manufacturer. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, then you may be entitled to any implied warranties allowed by law for the Warranty Period. Some states do not allow limitations on how long an implied Limited Warranty lasts, so the ab...