Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
The CGETF10xx-10x is also designed to be installed in the Transition Networks PointSystem™ chassis. Part Number Port One - Copper Port Two - Duplex Fiber-Optic CGETF1013-105 RJ-45 1000Base-T SC, 1000Base-SX, 850 nm multimode 100 m (328 ft)* 300 m (984 ft)* (62.5/125 .m cable) 500 m (1,640 ft)* (50/125 .m cable) CGETF1014-105 RJ-45 1000Base-T SC, 1000Base-LX, 1310 nm single mode 100 m (328 ft)* 10 km (6.2 miles) * CGETF1015-105 RJ-45 1000Base-T SC, 1000Base-LX, 1310 nm single mode 100 m (328 ft)* 25 km (15.5 miles)* CGETF1017-105 RJ-45 1000Base-T SC, 1000Base-LX, 1550 nm single mode 100 m (328 ft)* 65 km (40.4 miles) * CGETF1018-105 RJ-45 1000Base-T MT-RJ, 1000Base-SX, 850 nm multimode 100 m (328 ft)* 300 m (984 ft)* (62.5/125 .m cable) 500 m (1,640 ft)* (50/125 .m cable) CGETF1024-105 RJ-45 1000Base-T SC, 1000Base-SX, 1300 nm extended 100 m (328 ft)* multimode, 2 km (1.2 miles)* Note: 62.5/125 .m (fiber only) CGETF1035-105 RJ-45 1000Base-T SC, 1000Base-LX, 1550 nm single mode 100 m (328 ft)* 125 km (77.5 miles)* CGETF1039-105 RJ-45 1000Base-T LC, 1000Base-SX, 850 nm multimode 100 m (328 ft)* 300 m (984 ft)* (62.5/125 .m cable) 500 m (1,640 ft)* (50/125 .m cable) *Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network installation. NOTE: The stand-alone version of the media converter is SGETF10xx-10x. For more information, see the SGETF10xx-10x user’s guide on-line at: Installation . . . . . . . . . . . . . . . .2 Operation . . . . . . . . . . . . . . . .5 Cable Specifications . . . . . . . . .8 Technical Specifications . . . . .9 Troubleshooting . . . . . . . . . . .10 Contact Us . . . . . . . . . . . . . . .11 Compliance Information . . . .12 CGETF10xx- Part Number CGETF1029-105 Port One - Copper RJ-45 1000Base-100 m (328 ft)* Port Two - Single SC, 1000Base-LX, single mode, 20 km (12.4 miles)* CGETF1029-106 RJ-45 1000Base-T 100 m (328 ft) * SC, 1000Base-LX, 1550 single mode, 20 km (12.4 miles)* The CGETF1029-105 and the installed in the same network, where and the other is the remote converter. CGETF1029-107 RJ-45 1000Base-T 100 m (328 ft)* SC, 1000Base-LX, 1310 TX/1550 RX single mode, 40 km (24.8 miles)* CGETF1029-108 RJ-45 1000Base-T 100 m (328 ft)* SC, 1000Base-LX, 1550 TX/1310 RX single mode, 40 km (24.8 miles)* The CGETF1029-107 and the CGETF1029-108 are to installed in the same network, where one is the local converter and the other is the remote converter. * Typical maximum cable distance. Actual distance is dependent characteristics of the network installation. (TX = transmit, RX = receive) Installation CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the jumper and the 4-position switch and when installing the CGETF10xx-10x media converter into the PointSystem™ chassis. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter. Set the 3-position jumper • The jumper is located on the media converter circuit board. • Use small needle-nosed pliers or a similar device to set the jumper. • Refer to the drawing below for the jumper positions. Hardware The media converter mode is S determined by the 4-position switch H settings (as described on page 3) . Hardware Mode Software The media converter mode is determined by the most-recently saved, H S on-board microprocessor settings. Software Mode 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- Continued Set the 4-position • The 4-position switch is Copper Mode: up = Full Duplex Pause: up = Enable located on the side of the Link Pass- Through: up = Enable media converter. Fiber Auto-Negotiation: up = Disable • Use a small flat blade screwdriver to set the recessed switches. 1234 1. Twisted-Pair Full/Half Duplex Mode up = Full-Duplex on the copper link (see page 6) . down = Half-Duplex on the copper link (see page 6) . 2. Pause up = Enable Pause (see page 7) . down = Disable Pause. 3. Link Pass-Through up = Enable Link Pass-Through (see page 6) . down = Disable Link Pass-Through. 4. Fiber Auto-Negotiation up = Disable Auto-Negotiation for the fiber link (default setting). down = Enable Auto-Negotiation for the fiber link. If the CGETF10xx-10x is connected via fiber to another CGETF10xx-10x, both media converters must have the fiber Auto-Negotiation setting disabled (switch 4 = up) . Otherwise, the fiber-linked media converters will not link up. When Fiber Auto-Negotiation is disabled (default setting) : Switches 1, 2 and 3 will function only if Fiber Auto-Negotiation is disabled. The settings for Twisted-Pair Full/Half Duplex, Pause, and Link Pass-Through can be set as needed using switches 1, 2 and 3. When Fiber Auto-Negotiation is enabled: Switches 1, 2, and 3 will not function and the media converter adopts the settings for Twisted-Pair Full/Half Duplex, Pause, and Link Pass-Through from the media converter at the other end of the fiber cable. Fibe...