Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
FIG. 1 shows the front and rear panel views. ID button Status LED IR Receiver Ethernet Ethernet Speed and S-Video OUT IR/Serial port Analog stereo audio Link Activity LEDs RS232/422/485 port OUT (BNC) (front) LCD Displa LCD DisplaLCD Display yy Composite Input/Output port 12 VDC Power (rear) FIG. 1 MAX-CSD10 Video Decoder (front and rear views) Note: This unit can be mounted onto either a flat surface or into an equipment rack by first removing the front screws and then attaching it to an AC-RK. MAX-CSD10 Specifications (Cont.) Rear Panel Connectors (Cont.): • RS-232/422/485: Single 9-pin (DB9) port supports RS-232/422/ 485 data output including: -300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, and 115,200 Baud rates -7 or 8 Data bits -1 or 2 Stop bits -Even, Odd, Mark, Space, and None parity settings -CTS and RTS handshaking - XON/XOFF handshaking • I/O: Two digital binary Input/Output ports for contact closure (accepts a 4-pin 3.5mm mini-Phoenix (male) captive-wire connector). Each input is capable of voltage sensing. Inputformat is software selectable with interactive power sensing forIR ports. Operating/Storage• Operating Temperature: 0° to 45° C (32° to 113° F) Environment: • Storage Temperature: -30. to 70. C (-22. to 158° F) • Operating Relative Humidity: 5% to 85% (non-condensing) • Operation intended for indoor use only. Included Accessories: • 2-pin 3.5 mm mini-Phoenix female PWR connector • 4-pin 3.5 mm mini-Phoenix female I/O connector• BNC to RCA Adapter • CC-NIRC IR Emitter cable • MAX-CSD10 Quick Start Guide Other AMX Equipment: • AC-RK Accessory Rack Kit (FG515) • CSB Cable Support Bracket (FG517) • PMB Pole Mount Bracket (FG531) • STS, Serial To Screw Terminal (FG959) • Surface Mount Bracket Accessory (FG525) Wiring Installation Procedures The wiring parameters for the PWR, Serial, and Ethernet ports are described in detail within the following sections. Wiring The Power Connector Use an external power supply (see Power Requirements) to provide power to the MAX-CSD10 through the rear 2-pin 3.5 mm mini-Phoenix connector (FIG. 1). The incoming PWR and GND cable from the power supply must be connected to the corresponding locations within the PWR connector. Power-Over-Ethernet (POE) Connection Caution: If using Power-over-Ethernet as your source of power, you must FIRST ground the unit to provide ESD protection. Install only a single wire into the (-) GND side of the rear green 2-pin PWR connector, and then connect the terminal-end of this same wire to a grounded source. It is recommended that the length of this wire NOT exceed 6 ft. (1.83 m). Any 802.3af-compliant POE switch (such as the NXA-ENET24 POE) can automatically detect the 802.3af-compliant MAX device by its authenticated POE signature and sense its required load before turning on DC power to the POE Ethernet port. Note: Power-over-Ethernet connections work with all existing Category 3, 4, 5, 5e or 6 network cabling, including patch cables and patch-panels, outlets, and other connecting hardware, without requiring modification. Reading the Ethernet LEDs The MAX-CSD10 uses a standard CAT5 Ethernet cable to provide 10/100 network connectivity between the encoder and the network (FIG. 2). MAX-CSD10 (FG2178-72) Specifications Dimensions (HWD): 1.58" x 5.54" x 6.95" (4.01 cm x 14.07 cm x 17.65 cm) Power Requirements: • 500mA @ 12VDC (6W) • Power Over Ethernet (POE) is available. • Optional 12VDC power input overrides POE when used. • Power requirements are usage dependant. • This product is intended to be supplied by a Listed external power supply rated from 10 to 18 VDC, minimum 500 mA or equivalent. Weight: • 2.02 lbs (0.92 kg) Enclosure: • Metal with black matte finish Certifications: • FCC Part 15 Class B, CE, and UL listed Video Outputs: • Composite Video (via BNC) • S-Video (via standard female S-Video connector) Audio Outputs: • Analog Stereo (RCA connectors - Red/White) Supported Resolutions: • NTSC (480i) • PAL (576i) Supported Video Codecs: • MPEG2 (2 Mbps - 6 Mbps) • MPEG4 (500Kbps - 3 Mbps) Supported Audio Codecs: • MPEG Audio Level 2 (MP2) • MPEG Audio Level 3 (MP3) • AAC Front Panel Components: • ID Pushbutton: Used to both set the NetLinx ID (Device only) assignment and reset the unit back to its factory defaults. • Status LED: Green LED blinks to indicate both the system andcommunication status with the target Master. • LCD Display: Provides system information such as the currently used IP Address. • IR Receiver: Receives 38KHz AMX IR codes. Rear Panel Connectors: • COMPOSITE OUT: Composite Video Output (NTSC or PAL) via a female BNC connector. • 12VDC PWR: Single 2-pin 3.5mm mini-Phoenix (male) captive- wire connector from an optional 12 VDC power supply(overrides POE). • S-VIDEO OUT: Mini-Din4 port for composite S-Video output. • ETHERNET 10/100: Single RJ-45 port provides 10/100 Mbpsnetwork communication and POE. LEDs show communication activity, connections, speeds, and mode information (FIG. 2). • AUDIO R/L: Two...