Évaluations - , GPA:
(
)
)
Fabricant : Heath Zenith
Taille : 417.51 kb
Nom Fichier : e6120eea-d981-4fc4-9097-fa0b7d3b7600.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
• Tested and approved for outdoor use. • Eight selectable channels available, so multiple switches can be used in the same home. • Allows remote or dusk-to-dawn operation. • Car visor clip included for convenience. Car Visor LED Indicator Light ON Switch OFF Switch Auto Device Switch Receptacles 12-Volt (A23 Type) Battery (Included) Operation Eight selectable channels allow the user to Positive Terminal operate several systems at different locations in your home. If purchasing more than Tab Batteryonewirelesscontrolsystem,selectdifferent Chamber operating channels for each system or they (Type A23) will interact with each other. Battery 1. Remove Tab from Battery Chamber. Cover Remove cover from back of transmitter by pressing on it with your thumb and sliding it off as shown in Figure 1. Gently pull tab out of battery chamber. Slide cover onto transmitter. 2. PluginOutdoorModule.Remember,theoutdoormodulerequiresagrounded outlet. If you do not have a grounded outlet, you should contact an electrician to upgrade your electrical system for your safety. See precautions before using module (see page 2). 3. Mount Outdoor Module. Hang module with two nails or screws. There are two keyholes on the back for this purpose (see Figure 2, page 2). DO NOT allow module to hang by cord. Manual Switch Clip Remote Control Light Sensor Cover Grounded Plug Outdoor Module Figure 1 ON DIP 1 2 3 4 ON DIP 1 2 3 4 © 2007 HeathCo LLC 598-1108-05 4. Plug in devices you wish to control. Caution: Do not exceed the maximum load limits listed in Specifications section (see page 4). 5. Check operation. Place hand over light sensor cover. The unit should switch on. To check remote operation, toggle left switch to manual. Toggle ON/OFF switch. 6. Remote Control Functions. Automatic Mode: Toggle left switch to automatic to allow switched devices to come on at dusk and turn off at dawn. This is the default mode when first powered up or after power outage. Manual Mode: Toggle left switch to manual to allow operator to manually switch devices on and off. Use right toggle to switch devices on and off. Note:LEDwilllightwhentoggleswitches are pushed. Precautions When Using Outdoor Module • The module must be oriented with the power outlet down to prevent rain from entering the unit (see Figure 2). • The module must be located below the wall outlet as shown. This is to prevent rain from running down the cord into the wall outlet. • Note: The National Electrical Code and Canadian Electrical Code (and most local codes) require that outside outlets be protected by a Ground Fault Inter- Figure 2 rupter (GFI). Car Visor Clip The remote control is equipped with a removable car visor clip for added con venience. The car visor clip may be removed to allow the remote to lie flat on table tops or other horizontal surfaces. 1. Attach car visor clip to car visor as shown in Figure 3. 2. To remove car visor clip. Insert a small flat-head screw driver into slot on back of remote. Gently push portion of clip inside of remote with screwdriver while pulling clip out of remote from top (see Figure 4). Power Outlets Keyholes to Hang Unit Remote Screwdriver Control Car Visor Visor Clip Figure 3 Figure 4 2 598-1108-05 Channel Settings Note: Most installations will not require you to change any of the dip switches on your plug-in module or remote control. The remote control and outdoor modulecommunicatebyusingchannels that can be changed by sliding dip switches into the ON or OFF [on some switches the numbers 1 (ON) and/or 0 (OFF) are used] position on both the remote control and outdoor module. The channel is factory set; however, there are 3 switches (8 selectable channels) that allow you to expand your system and prevent outside interference. Other wireless productsmaycauseinterferenceand thesystemmaynotfunctionproperly. Follow the instructions below for setting a new channel. outdoor module (see Figure 5). 1. Open the cases and locate dip switches on both the remote control and 2. The remote control and outdoor module both have two positions (ON and OFF) on each of the four dip switches. Dip switches 1 through 3 are used for setting the channel. Use the table below to set channel 2 after setting channel 1. Note: The channels must be programmed according to the table below for all 4 functions of the remote control to work properly. The receiver(s) must match the code settings for channel 1. Use the table below to set the 3. To change the channel, slide dip switches to ON or OFF as needed. It is recommended to only change one dip switch at a time and then check to see if the system is functioning properly. Note: Dip switches in positions 1 through ON 1234 Access Door Dip Switches - Shown in the OFF Position (Factory Default) Keyholes ON DIP 1 2 3 4 ON DIP 1 2 3 4 Figure 5 ON 1 2 3 4 Channel Setting Codes Channel 1 Transmitter Channel 2 and Receiver(s) Transmitter 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 0 = OFF 1 = ON correspond...