Log:
Évaluations - 3, GPA: 4 ( )

Instructions Denon, Modèle AVR-487

Fabricant : Denon
Taille : 1.79 mb
Nom Fichier : d8ec6677-10e5-4c9a-9e7c-66a162ef9f16.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Subwoofer Center speaker Surround speaker Front speaker Set these at the sides of the monitor or screen with their front surfaces as flush with the front of the screen as possible. 6 ENGLISH ENGLISH Easy Operation Easy Operation Speaker connections NOTE: When making connections, take care none of the individual conductors of speaker cable come in contact with adjacent terminals, with other speaker cable conductors, or with the rear panel and screws. NEVER touch the speaker terminals when the power is on. Doing so could result in electric shocks. Connecting the speaker cables 1. Loosen by turning counterclockwise. Either tightly twist or terminate the core wires. 2. Insert the cable. 3. Tighten by turning clockwise. Connect the speaker making sure that like polarities < with < , > with > ). Connecting banana plugs Turn clockwise to tighten, then insert the banana plug. . Speaker impedance Speaker Impedance Front A, B 6 ~ 16 ./ohms Front A+B 12 ~ 16 ./ohms Center 6 ~ 16 ./ohms Surround Note on speaker impedance When using speakers with an impedance below the designated value (for example 4 ./ohms), playing for long periods of time with the volume high could cause the temperature to rise, activating the protection circuit. When the protection circuit is activated, the output to the speakers is cut off and the power indicator blinks. If this happens, unplug the power cord, wait for the set to cool off and improve ventilation around the unit. Also check the wiring of the input cables and the speaker cables. After doing this, plug the power cord back in and turn the unit’s power back on. If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center. . Connections • With the AVR-487, up to six speakers • When making connections, Subwoofer Center speaker Surround speakers > < < > > < < > > < > < > < IN ( L) ( R) ( L) ( R) ( L) ( R) Connection terminal for subwoofer with built-in amplifier. Front speakers (B) Front speakers (A) 7 ENGLISH Easy Operation Easy Operation 8 ENGLISH ENGLISH • For best picture quality (especially with progressive DVD and other high definition sources), choose the component video connection to your monitor. S-Video and composite video outputs are also provided if your monitor does not have component video inputs. • The signals input to the color difference (component) video terminals are not output from the VIDEO output terminal (yellow) or the S-Video output terminal. Connecting a DVD player and monitor • To connect the digital audio output from the DVD player, you can choose from either the coaxial or optical connections. If you choose to use the coaxial connection, it needs to be assigned. For more information about Digital Input Assignment ( page 19). • Precaution when using S-Video terminals AVR-487’s S-Video terminals (input and output) and video terminals (input and output) have independent circuit structures, so that video signals input from the S-Video terminals are only output from the S-Video terminal outputs and video signals input from the pin terminals are only output from the pin terminal outputs. When connecting this unit with equipment that is equipped with S-Video terminals, keep the above point in mind and make connections according to the equipment’s instruction manuals. Audio signal flow is shown with white arrows, video signal flow is shown with gray arrows. • Connect a non-DVD video disc player (such as a laser disc, VCD/SVCD, or future high definition disc player) to the DVD/VDP terminals in the same way. • The component video input and/or output terminals may be labelled differently on some monitors or video components. Check the owner’s manuals for other components for further information. DVD player S VIDEO OUT R L AUDIO OUT VIDEO OUT COMPONENT VIDEO OUT Y PB PR OPTICAL OUT F H G D R L R L A S VIDEO IN VIDEO IN Monitor TV COMPONENT VIDEO IN Y PB PR F H G ENGLISH Easy Operation INPUT SELECTOR INPUT MODE VOLUME [ON/SOURCE] INPUT SELECTOR Before operating 1 1 Turn on your subwoofer. Set the volume to halfway and frequency to the maximum or Low pass filter the output volume and the crossover Some subwoofers have a standby mode. function off before performing the Auto 2 2 Turn on your monitor. 3 3 Press < POWER> . . ON: The power indicator lights red. . OFF: The power turns off and the indicator is off. Easy Operation Playing the 1 1 Use INPUT SELECTOR to select the input source you want to play. 2 2 Press INPUT MODE. AUTO PCM DTS EXT. IN ANALOG Press < ANALOG> to select “ANALOG”, < EXT. IN> to select “EXT. IN”. 3 3 Start playback on the selected component. For operating instructions, refer to the component’s manual. 4 4 Use VOLUME to adjust the volume. • The volume level is displayed on the master volume level display. 4 4 Press < ON/STANDBY> or [ON/SOURCE] . • The power indicator blinks green and...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories