Once a source has been selected, the Select Source Type screen will be displayed. The menu selection immediately defaults to the Learn IR selection in the first screen of the Select Source Type screen (FIG. 25). The source number is displayed at the top of the screen. FIG. 25 Select Source Type - Learn IR .. Learn IR will allow user to learn IR commands for the selected source .. Delay allows user to add a delay to all IR commands learned for the selected source type .. Label allows customizatio

31. Currently used IP Address Firmware upload in progress Device is idle, no stream in progress Device is currently streaming Device is currently rebooting Device is being reset to its factory default settings and then rebooting FIG. 31 LCD status messages MAX-CSE/MAX-CSD10 Operation/Reference Guide Configuring Communication Configuring the MAX Communication Parameters Although the unit is initially configured to obtain the first available DHCP Address, it is recommended that after the initial c

MAX-CSE/MAX-CSD10 Operation/Reference Guide MAX-CSE Web Interface Stream Profiles Page The Stream Profiles page (FIG. 16) is accessed by clicking on the Stream Set-Up button in the Navigation Bar. The Stream Profiles page allows users (with the proper access rights) both to configure the properties of the outgoing media stream and set up the properties associated with communicating that stream to an external IP-enabled device capable of receiving and processing the data. FIG. 16 Stream Profiles

25). Channel Prev Display the Preset screen where the user can select 1 of 10 available presets Displays the Home screen Display Line #1 - Channel #, Name Display Line #2 - Artist, Song Title, Composer Channel Next Display the Numeric screen where the user can enter the channel number directly Displays the SIRIUS MORE screen FIG. 25 LCD Keypad - SIRIUS SAT Main screen Display Line #1 Channel # & Channel Name Channel # + Channel Name will be displayed up to a max. of 14 characters. .. This displa

It utilizes buffered outputs to provide signal integrity when distributing data and video to plasma displays, projectors and monitors. By using true, high-quality VGA cable, signal and picture quality can be extended over long distances. The AVB-DA-RGBHV-0102 also comes complete with an external 12V power supply. (front) SOLECIS AVB-DA-RGBHV-0102 ©-Î-® T ö O I—Video IN Video OUT 1-i FIG. 1 Solecis AVB-DA-RGBHV-0102 Power connector Video OUT 2 r* (rear) Common Application The AVB

11. Only use attachments/accessories specified by the manufacturer. 12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way,

6 Connecting SWT Speakers.............................................................................................. 6 Connecting Non-SWT Speakers...................................................................................... 6 Connecting To a Tango Audio Controller................................................................. 6 Connecting SWT Keypads......................................................................................... 6 Wiring Diagram - Single Amplifier....

Op eration/Reference Guide Tango Amplifiers DAS-TAMP4-SIG Tango 4-Channel Amplifier DAS-TAMP8-SIG Tango 8-Channel Amplifier Tango Distributed Audio Last Revised: 2/10/2010 AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP's or other AMX authorized entity. AMX warrants its products to be free of defects in material and workmanship under n

Any overhang will affect the installation of the covering sheetrock, as well as affect the placement of the Plastic Back Box. The Rough-In Box has two sets of knockouts in the top and bottom, one of the set for US wiring and one for international wiring. Note: Make sure that the power cable has been pulled through the Rough-In Box by the resident electrician before continuing the installation. After completing the installation of the Rough-In Box, install sheet rock or other wall material over

The red TV Sensor indicator, located on the front panel, should be dark. 3. Turn the television on. 4. Turn the POT screw counterclockwise until the TV Sensor indicator lights. Then, turn the POT screw counterclockwise one full turn. 5. Turn television power off. If the TV Sensor indicator is lit, turn the POT screw clockwise until the indicator goes dark. 6. Reattach the enclosure and refasten the two screws. IR Signal Attenuation Adjustment If you experience television control problems after c