The sound card’s documentation should help you determine which outputs to use with your speaker system. 1. Make sure the power to your computer is turned off. 2. Locate the lime green 3.5 mm stereo cable provided with your speaker system. 3. Connect one end of the lime green 3.5 mm stereo cable to the matching jack on the back of the right satellite, and the other end to the lime green output labeled “FRONT” on your sound card. Portable Audio Devices (MP3, Portable CD Players, etc.) 1. Make sure

The lower the am: -’s output impedance, the fa;- :.he overshoot of the voice < ! dampen out. The output h ce of an amplifier can be lated by dividing the rated ut impedance, typically : us, by the damping factor. Tj 4B has a damping factor of 200 which correspond: n output impedance of 0.04 3.5.1 Calculi g the Maximun ngth of Cable fo : Specified ALTEC LANSING* CORPORATION ® a Mark IV Company 3 Operating and Service Instructions for the Altec Lansing 9444B Power Amplifier Table I 9444B Po

It is difficult, however, determine the proper fuse va! with the correct time lag a:; overload characteristics to mat the limitations of a speaker sy tem. The values shown in Table I should serve only as a guide. 4 ALTEC LANSING* CORPORATION • a Mark IV Company Operating and Service Instructions for the Altec Lansing 9444B Power Amplifier INPUT POWER AMPLIFIER STEP-UP TRANSFORMES 70. 100. 140, OR 210 VOLTS LONG CABLE RUN (SHALL GAUGE WIRE) LOUDSPEAKER STEP-DOWN TRANSFORMER Figure 5 Hi

O. Box 26105 o Oklahoma Cily. OK « 73126-0105 USA © Tel: (405) 324-5311 e FAX: (405) 324 Operating and Service Instructions for the Altec Lansing 9441A Power Amplifier Table of Contents 1 ELECTRICAL..............................................................' 1 1.1 120 V ac, 50/60 Hz Power Connections..............................................................................1 1.2 220/240 V ac, 50/60 Hz Power Connections...................................................................

Suite 362 Oklahoma City, OK 73116 USA A division of Altec Lansing Technologies Inc, Milford PA 18337-0277 Made In USA Operating Manual 6125A and 4200A Multi-Channel Power Amplifier Table Of Contents 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3 AC POWER REQUIREMENTS . . . . . . . . . . . . . . . . . .

For example, Channel 1 and Channel 2 together can provide stereo, mono, or bridged operation, completely independent of Channels 3-4 or Channels 5-6 settings. 7.4 50Hz Low Cut Switch Each pair of channels has a 50Hz second order (12 dB per octave) low-cut filter option which is applied to both channels within the pair. When the switch is pressed, the audio signal is -3dB at 50Hz, -15dB at 25 Hz, -27dB at 12.5Hz, etc. 8 Operating Manual 6125A and 4200A Multi-Channel Power Amplifier 7.5 Input Leve

This makes it easy to properly adjust the gain for each input module while efficiently using the rest of the system in terms of performance and headroom. Figure 7. Block Diagram of 1707C/1715C Mixer/Power Amplifiers The mixer/power amplifier then sums the signal at the wiper of each input channel level control into a true virtual ground summing node or bus. The summing amplifier has eight input channels — input channels one through six on the front panel, tone generator output, and the link in

1 kHz) ±1 dB, 20 Hz - 20 kHz (1 watt output) ±1 dB, 20 Hz - 20 kHz (0.775 Vrms output, 600 fl load) (Ref 1 kHz) <0.05%, 20 Hz - 20 kHz (rated output power, 30 kHz low-pass filter) <0.05%, 20 Hz - 20 kHz (0.775 Vrms output, 600 fl load, EQ flat, compressor/-limiter off, 30 kHz low-pass filter) >80 dB below rated output power, A-weighted >75 dB below 0.775 Vrms output, A-weighted, EQ off, compressor/limiter off DESCRIPTION The Altec Lansing 1707C/I715C Mixer/Power Amplifier is a six channe

The amplifier provides outputs for 4-ohm, 8-ohm and 16-ohm loudspeakers, plus a 70-volt line output for distribution systems. In addition to the high-impedance input, the amplifier has an octal socket to accept a line-isolation transformer. A selectable high pass filter is included for use in speech systems. Cut-off frequency of the filter is 300 Hz. The 1593C is capable of operation from a 120V or 240V ac source or a negative grounded 28V dc source, and features silent, automatic transfer to