Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
REVISED 4/99 G1033 20" Planer -27 TROUBLESHOOTING This section covers the most common processing problems encountered in planing and what to do about them. Do not make any adjustments until planer is unplugged and moving parts have come to a complete stop. SYMPTOM POS CAUSE SIBLECO ACTION RRECTIVEMotor will not start. 1. 2. Low voltage. Open circuit in motor or loose connections. 1. 2. Check power line for proper voltage. Inspect all lead connections on motor for loose or open connections. Motor will not start; fuses or circuit breakers blow. 1. 2. 3. Short circuit in line cord or plug. Short circuit in motor or loose connections. Incorrect fuses or circuit breakers in power line. 1. 2. 3. Inspect cord or plug for damaged insulation and shorted wires. Inspect all connections on motor for loose or shorted terminals or worn insulation. Install correct fuses or circuit breakers. Motor overheats. 1. 2. Motor overloaded. Air circulation through the motor restricted. 1. 2. Reduce load on motor. Clean out motor to provide normal air circulation. Motor stalls (resulting in blown fuses or tripped circuit). 1. 2. 3. 4. Short circuit in motor or loose connections. Low voltage. Incorrect fuses or circuit breakers in power line. Motor overloaded. 1. 2 3. 4. Inspect connections on motor for loose or shorted terminals or worn insulation. Correct the low voltage conditions. Install correct fuses or circuit breakers. Reduce load on motor. Machine slows when operating. 1. 2. Feed rate too high. Depth of cut too great. 1. 2. Feed workpiece slower. Reduce depth of cut. Loud, repetitious noise coming from machine 1. 2. 3. Pulley setscrews or keys are missing or loose. Motor fan is hitting the cover. V-belt is defective 1. 2. 3. Inspect keys and setscrews. Replace or tighten if necessary. Tighten fan or shim cover. Replace V-belt. See Maintenance. Machine is loud when cutting. Overheats or bogs down in the cut. 1. 2. Excessive depth of cut. Knives are dull 1. 2. Decrease depth of cut. Sharpen knives. Infeed roller marks are left on the workpiece. Depth of cut too shallow. Increase depth of cut. Outfeed roller marks are left on right side of workpiece. Too much spring tension on feed roller. Refer to Adjustments, Spring Tension. Cannot control snipe. Long or heavy board sags as it enters and exits. Lift up on unsupported end of board as it enters and exits cutter- head. Chip buildup on outfeed roller. Chips working their way back under the chip deflector. Lay duct tape over the mounting bolts along the outside edge to seal any possible gaps. Machine howls on startup. Chip deflector too close to the cutterhead. Move back 1/8" to 1/4" from the cutterhead. Table moves down while cutting. Knives dull Replace knives. -28-G1033 20" Planer 36 37 38 21 44 25 43 1 96 2 97 38 82 81 14 47 37 38 46 44 76 77 75 57 73 37 29 62 63 64 98 66 68 67 35 61 60 58 58 57 57 38 37 56 107 95 95 107 59 54 55 37 38 15 23 80 80 83 85 84 85 15 23 38 37 24 25 23 22 17 23 42 19 20 19 20 40 34 18 20 19 32 39 19 69 109 87 92 93 86 95 88 94 70 25 16 40 51 48 50 3 49 4 13 12 108 89 52 53 5 6 8 78 7 26 26 30 33 35 41 65 79 90 REF PART # DESCRIPTION REF PART # DESCRIPTION 01 P1033001 HEADCASTING 02 PSS13M SETSCREW M10-1.5 X 12 03 P1033003 CUTTERHEAD 04 P1021103 SPRING 05 P1033005 BLADES FOR PLANER 06 P1033006 GIB 07 PB17M HEX BOLT M8-1.25 X 10 08 P1021166 KNIFE GAUGE W/BAR 12 P6206 BEARING 6206 13 PK09M KEY 8 X 8 X 36 14 P1021007 CUTTERHEAD PULLEY 15 P1033015 WASHER 5/16" X 13/16" 16 PSS12M SETSCREW M6-1.0 X 25 17 P1021008 MOTOR PULLEY 18 P1033018 INFEED ROLLER 19 P1021153 BUSHING BLOCK 20 P1021152 SPRING 21 P1033021 SPECIAL SETSCREW 22 P1021092 PLATE 23 PB09M HEX BOLT M8-1.25 X 20 24 PSS11M SETSCREW M6-1.0 X 16 25 PN01M HEX NUT M6-1.0 26 PK21M KEY 5 X 5 X 23 29 PB18M HEX BOLT M6-1.0 X 15 30 P1033030 OUTFEED ROLLER 31 P1021149 SPROCKET 32 P1033032 LOCKING ROD 33 PR03M SNAP RING 12MM 34 P1033034 CHIP BREAKER 35 PN09M HEX NUT M12-1.75 36 P1021028 CHIP BREAKER SPRING 37 PW03M FLAT WASHER 6MM 38 PB03M HEX BOLT M6-1 X 12 39 P1033039 SHAFT 40 P1033040 BRACKET 41 P1033041 PRESSURE PLATE 42 PLW04M LOCK WASHER 8MM 43 P1033043 SHAFT 44 PSS11M SETSCREW M6-1.0 X 16 45 PSS11M SETSCREW M6-1.0 X 16 46 P1033046 SPRING PLATE 47 P1033047 CHIP DEFLECTOR PLATE 48 P1021161 ANTI-KICKBACK FINGER 49 P1021160 SPACER 50 P1033050 SHAFT 51 PEC06M E-CLIP 20MM 52 P1033052 DEPTH LIMITER 53 PFH02M FLT HD SCR M6-1.0X12 54 P1033054 UPPER COVER 55 P1033055 GASKET 56 P1033056 COLLECTOR 57 P1033057 ROLLER STAND 58 P1033058 ROLLER 59 PSB01M CAP SCREW M6-1.0 X 16 60 P1033060 WORM GEAR BOX 61 PSB37M CAP SCREW M6-1.0 X 50 62 P1033062 WORM 63 P6201 BEARING 6201 64 PR29M SNAP RING 32MM 65 PK05M KEY 4 X 4 X 10 66 P1033066 HANDWHEEL 67 P1033067 WASHER 1/2" X 11/8" 68 P1021032 HANDLE 69 P1033069 SCALE 70 PS08M PHLP HD SCR M5-0.8X12 73 P1033073 COVER 75 P1033075 SAFETY HATCH 76 PB04M HEX BOLT M6-1.0X10 77 P1033077 SAFETY HATCH 78 PSB12M CAP SCREW M8-1.25 X 16 79 P1033079 PULLEY GUARD 80 P1033080 STUD 81 PW07 FLA...