Log:
Évaluations - 2, GPA: 4 ( )

Instructions Beko, Modèle DRCS 76 S

Fabricant : Beko
Taille : 789.53 kb
Nom Fichier : 82cb9530-7829-43b4-b367-593d8a4bd978.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


• Clean lint screen before or after each load. • Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. • The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel. • Never use the dryer without the lint filter. SAVE THESE INSTRUCTIONS 3 Installation Appropriate installation location • Install your machine in environments which have no risk of freezing and in a stable and level position. • Do not place your machine on a long pile rug or on similar surfaces. • Operate your machine in a well ventilated, dust-free environment. • Do not block the air ducts in front of and under the machine with materials such as long pile rugs or kitchen unit plinths. B Make sure that your machine is not placed on the power cable. B Keep at least 3 cm from the edges of other furniture. Under Counter Installation • Leave at least 3 cm of space between the side and rear walls of the machine and the walls of the counter/cupboard when installing your machine under a counter or in a cupboard. Never use the tumble dryer without top plate. Adjusting the feet In order to ensure that your machine operates more silently and vibration-free, it must stand level and balanced on its feet. Front feet of your machine can be adjusted. Balance the machine by adjusting the feet. 1. Loosen the feet by hand. 2. Adjust them until the machine stands level and firmly. C Do not use any tools to loosen the adjustable feet. Otherwise, they can be damaged. C Never unscrew the adjustable feet from their housings. 2 plastic pieces supplied together with the Operating Instructions prevent your machine from slipping on wet and slippery surfaces. To install these plastic parts: 1. Tilt your machine to backwards. 2. Fit the plastic parts to the front adjustable feet. Press on the plastic parts to fix them in their places. 3. Check the balance of your machine again and readjust the adjustable feet if necessary. Ventilation hose and connection (for products equipped with an outlet vent) Ventilation hose assures exhausting of the air from inside the machine. Vented dryer has 1 air outlet. Stainless sheet metal or aluminum pipes can be used instead of the hose. The diameter of the pipe to be used should be minimum 10 cm. Maximum hose and pipe lengths are given in the table below. Hose Pipe Maximum length 4 m 5 m 1 elbow 45° -1.0 m -0.3 m 1 elbow 90° -1.8 m -0.6 m 1 elbow 90° short -2.7 m 1 wall passage -2.0 m -2.0 m C Each elbow and other passages should be subtracted from the above maximum length. To connect a ventilation hose; 1. Connect the air outlet hose to the hose spacer piece by turning it anti- clockwise. 2. Make the hose passages as shown below. C Exhaust of humid air from the dryer into the room is inconvenient. It may damage the walls and furniture in the room. C The ventilation hose can be routed outdoors via a window or it can be connected to an air outlet in the wall (see diagram below). C Air outlet hose must be extended directly to the outdoors. There must be a small number of elbows as not to hinder air ventilation. C To prevent water accumulation in the hose, make sure that it is not folded on the floor. B The air ventilation hose should not be connected to the chimney of a stove or a fireplace. B Do not operate your machine at the same time with heaters such as a coal or gas stove. Airflow may cause the chimney to flare up. Airflow may cause the chimney to flame up. Connection to a water drain (for products equipped with a condenser ) In products equipped with a condenser unit the water accumulated during the drying cycle is collected in the water tank. You should drain the accumulated water after each washing cycle. You can directly send the accumulated water out through the water drain hose supplied with the machine instead of periodically draining the water collected in the water tank. Connecting the water drain hose; 1. Remove the hose on the machine by pulling it out from its end. Do not use any tools to take out the hose. Attach the drain hose adaptor to the end of this hose. 2. Connect the special drain hose supplied with the machine to the hose adaptor fitting. 3. The other end of the drain hose can be directly connected to the wastewater drain or to the washbasin. The fitting must always be secured in all types of connections. Your house may be flooded if the hose gets out of its housing during water discharge. C When you direct the water drain out, “Water Tank” warning LED will light up at the end of each programme. Important: • The hose should be attached to a height of maximum 80 cm. • You must be careful not the pinch or bend the hose. • The end of the hose should not be bent, it should not be stepped on and it must not be folded between the drain and the machine. Destroying the packaging material Packaging material can be dangerous to children. Keep the packaging materials out of the reach of children or dispose of th...

Ce manuel est également adapté pour les modèles :
Avions - DRCS 76 W (789.53 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories