Évaluations - , GPA:
(
)
)
Fabricant : RIDGID
Taille : 2.32 mb
Nom Fichier : 96347b67-05aa-408a-ac74-06fbc91bab97.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
The cutter head removes material from the work- piece Depth of cut A term used to indicate how deep into the workpiece the cutter knives will cut. Fence The fence is attached to the jointer/planer base. The fence helps support and guide the workpiece as it is pushed across the cutter head. Freehand Using the tool without holding the workpiece firmly against the fence and table. This can let the workpiece twist and kick back and must never be attempted. Gum A sticky, sap based residue from wood products. Hold-Down/Push-Blocks They are required for your own safety. They are used to hold your workpieces against the table and fence when planing, rabbeting or jointing. Infeed Table The section of the jointer bed upon which the workpiece is placed before being pushed into the cutter head. Infeed table height is adjustable which allows the operator to select the depth of cut. Jointing The removal of wood along the edge of a board so as to make that edge straight, smooth and square to the board face which is against the fence. Kickback An uncontrolled grabbing and throwing of the workpiece back toward the operator by the rotating cutter head. Leading End The end of the workpiece which is pushed into the cutter head first. Outfeed Table The section of a jointer bed which supports the workpiece after it passes over the cutter head. Planing Removing wood from the widest surface or face of a board so as to make it flat and smooth. Rabbet A notch cut into the edge of workpiece. Resin A sticky, sap based substance that has hardened. Revolutions Per Minute (RPM) The number of turns completed by a spinning object in one minute. Throw-Back Throwing of pieces in a manner similar to a kickback. Trailing End The workpiece end last cut by the knives. Workpiece The item on which the cutting operation is being performed. The surfaces of a workpiece are commonly referred to as faces, ends and edges. Face Edge End Rabbet Motor Specifications and Electrical Requirements Power Supply and Motor Specifications WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15-amp branch circuit. Use a 15-amp time delay type fuse or circuit breaker. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately. The A/C motor used on this tool is a capacitor start, nonreversible type, wired at the factory for 110-120V AC, 60 Hz. operation. Follow the instructions on page 8 to connect the motor for 220-240V A/C operation. 7 Rated Horsepower 1 Voltage 110-120 220-240 Amperes 12 6 Hertz (Cycles) 60 Phase Single RPM 3450 Rotation of Shaft Counterclockwise Motor Specifications and Electrical Requirements (continued) General Electrical Connections DANGER: To reduce the risk of electrocution: 1. Use only identical replacement parts when servicing. Servicing should be performed by a qualified service technician. 2. Do not use in rain or where floor is wet. This tool is intended for indoor residential use only. WARNING: Do not permit fingers to touch the terminals of plug when installing or removing the plug to or from the outlet. If power cord is worn or cut, or damaged in any way, have it replaced immediately. 110-120 Volt, 60 Hz. Tool Information The plug supplied on your tool may not fit into the outlet you are planning to use. Your local electrical code may require slightly different power cord plug connections. If these differences exist refer to and make the proper adjustments per your local code before your tool is plugged in and turned on. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment grounding conductor and a grounding plug, as shown. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes WARNING: If not properly grounded, this tool can cause an electrical shock, particularly when used in damp locations, in proximity to plumbing, or out of doors. If an electrical shock occurs there is the potential of a secondary hazard, such as your hands contacting the knives. Changing Motor Voltage WARNING: If not properly grounded, this tool can cause an electrical shock, particularly when used in damp locations, in proximity to plumbing, or out of doors. If an electrical shock occurs there is the potential of a secondary hazard, such as your hands contacting the knives. NOTE: The jointer is prewired at the factory for 120V operation. Use the following procedure to change motor voltage. To change to 240V application an additional wire nut is supplied from the factory. This part is included in the loose parts. 1. Unplug the jointer/planer before making or changing any connecti...