5. Avoid dangerous environments. Do not operate this machine in wet or open flame environments. Airborne dust particles could cause an explosion and severe fire hazard. 6. Ensure all guards are securely in place and in working condition. 7. Make sure switch is in the “OFF” position before connecting power to machine. 8. Keep work area clean and free of clutter, grease, etc. 9. Keep children and visitors away. All visitors should be kept a safe distance away while operating unit. 10. Childproof w

1,510 Black Walnut............ 1,410 Red Alder................1,370 Basswood................1,280 Cottonwood............. 1,160 Western Larch...........1,150 Tamarack.................1,130 Douglas Fir..............1,080 Alaska Cedar............1,050 Sitka Spruce.............1,000 Sugar Pine.................980 Cypress.....................940 Redwood (OG)............930 Red Cedar ................. 860 T White Pine.................850 SOFT Balsam Fir................. 710 Figure 32.

A JOINTER PAL® JOINTER KNIFE SETTING JIG INSTRUCTIONS FOR USE Preparation 1. Disconnect jointer from power source. 2. Move the jointer fence all the way to the rear of the jointer table. The fence should be aligned 90° to the outfeed table. The fences on some of the new jointers automatically align themselves when tightened, but older jointers often employ a ‘free floating” fence which should be carefully aligned perpendicular to the outfeed table. Jointer Pal will work without a fence, but

With proper care, the Mini Planer Pal® should provide you with years of reliable knife setting service. Do not try to use these jigs on larger diameter cutterheads since the preset knife height and curvature requirements will not be met. Planer Pal® offers larger, adjustable knife setting jigs for use on larger diameter cutterheads. CAUTION: The zinc coated neo-dymium magnets used in the Mini Planer Pals® are extremely strong, but they are very brittle. To avoid chipping the magnets, rock them

Make sure that the knife is at the lowest point of its cutting arc. 4. Note the reading on the dial indicator face. 5. Remove the dial indicator and place it in the same position at the opposite end of the knife. Read the dial indicator again. If the reading is not equal to the first one, adjust one side of the planer bed until the readings are the same at both ends of the knife. Adjusting Bed Rollers 1. Rotate the dial indicator to the “Down-reading” position (see Figure 2). 2. Place the d

Besides the data sheet and parts in this insert, the content in the Model W1754 owner's manual is the same for both machines. Before operating your new machine, you MUST read and understand this insert and the entire Model W1754 manual to reduce the risk of injury from improper use or setup. If you have any further questions about this manual insert or the differences between the Model W1754S and the Model W1754, contact our Technical Support at (360) 734-3482 or email tech-support@shopfox.biz.

5. As your leading hand gets within 4" of the cutterhead, lift the push block up and over the cutterhead and place it on the work- piece as it passes over the outfeed table. Do the same thing when your trailing hand nears the cutterhead and try to maintain pressure on the outfeed table. Never let your hands get closer than 4" from the cutterhead! 6. Repeat steps 4-5 until the surface is flat. OPERATIONS -23 OPERATIONS -24- Edge Jointing Edge jointing is passing the workpiece over the jointer on

Lift the cover off and set it aside. 4. Vacuum all dust and debris from the motor and belt areas. 5. Inspect the cutterhead belt for proper tension, straight alignment, and possible damage or wear. Note: The belt is properly tensioned if it deflects about -W when you press down on middle of the belt with moderate pressure from your thumb or forefinger. The belt is properly aligned if it lies flat and straight on the motor shaft and drive pulley. Belt damage will be evident on inspection. 6.

Contents INTRODUCTION..................................................................................................3 INTRODUCTION SET UPELECTRICAL SAFETYWoodstock Technical Support............................................................................ 3 Specifications............................................................................................... 4 Controls and Features..................................................................................... SAFETY............

9. Remove the wood that is holding the blade Top Dead Center Figure 25. Blade is positioned at its highestposition (Top Dead Center). Figure 26. Checking the blade height. Figure 27. Blade clamp screws. ADJUSTMENTS guard open. -19 Depth Of Cut The depth of cut is equal to the distance between the infeed table surface and the top of the cutterhead blade at top-dead-center (Figure 28). The depth of cut is adjusted by raising and lowering the infeed table. To adjust the depth of cut: • Turn the tab