Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
See figure 2. AXLE SPACER 5/8" FLAT WASHER 5/8" FLAT WASHER HUB CAP WHEEL NO CROSS HOLE HUB CAP 5/32" x 2" COTTER PIN CROSS HOLE 5/8" FLAT WASHER 8. Remove the nut from the middle bolt in the crossover tube. See figure 4. CROSSOVER TUBE MIDDLE NUT SHAFT SUPPORT MIDDLE BOLT PLATE 5 FIGURE 7 13. Assemble the leg stand tube to the handle tube (long) using two 1/4" x 1-1/2" hex bolts. Secure tightly with two 1/4" nylock nuts. See figure 6. 14. Place a vinyl cap over the end of the leg stand tube. See figure 6. FIGURE 5 FIGURE 6 15. Assemble the flow control link (end with small hole) to the flow control arm using a 1/4" x 1" hex bolt, a nylon washer and a 1/4" nylock nut as shown in figure 7. Tighten carefully. The flow control link should not be loose but should pivot with no more than slight resistance. HANDLE TUBE (LONG) 1/4" x 1-1/2" HEX BOLTS 1/4" NYLOCK NUTS VINYL CAP LEG STAND TUBE IMPORTANT: Do Not assemble handle tube to same side of crossover tube as shaft support plate. 9. Place the long handle tube onto the crossover tube on the side opposite from the shaft support plate. Fasten with the bolt, washer and nut removed in the previous step. See figures 4 and 5. Do not tighten at this time. 10. Assemble two handle braces to the inside of the hopper frame, one on each side, using two 1/4" x 1-1/2" hex bolts and two 1/4" nylock nuts. See figure 5. Do not tighten at this time. 11. Assemble the other end of the two handle braces to the long handle tube using a 1/4" x 1-1/2" hex bolt and 1/4" nylock nut. Do not tighten at this time. See figure 5. 12. Tighten all nuts and bolts in same sequence as assembled in steps 9 through 11. See figure 5. MIDDLE BOLT MIDDLE NUT HANDLE TUBE (LONG) HEX BOLT 1/4" x 1-1/2" HEX BOLT 1/4" x 1-1/2" HITCH BRACE 1/4" NYLOCK NUT CROSSOVER TUBE SHAFT SUPPORT PLATE FLOW CONTROL LINK FLOW CONTROL ARM 1/4" NYLOCK NUT 1/4" x 1" HEX BOLT SMALLEST HOLE NYLON WASHER 16. Assemble the flow control arm to the flow control mounting bracket using a 1/4" x 1" hex bolt, two nylon washers and a 1/4" nylock nut as shown in figure 8. Tighten carefully. The flow control arm should be snug, but should pivot with no more than a slight resistance. 17. Assemble the vinyl grip. See figure 8. 1/4" x 1" HEX BOLT 1/4" NYLOCK FLOW CONTROL MOUNTING BRACKET FLOW CONTROL ARM VINYL GRIP NUT (2) NYLON WASHERS FIGURE 8 18. Place a 5/16" flat washer onto the end of the flow 19. Hook the free end of the flow control rod through the hole in the slide gate bracket located near the bottom of the hopper. See figure 10. HOPPER SLIDE GATE BRACKET FLOW CONTROL ROD FIGURE 10 20. Assemble both the flow control mounting bracket and the short handle tube to the long handle tube. Use two 1/4" x 1-3/4" hex bolts, four 5/16" flat washers and two 1/4" nylock nuts as shown in figure 11. Do not tighten at this time. 21. Place a handle grip on each handle. See figure 11. FLOW CONTROL ROD FLOW CONTROL LINK 3/32" COTTER PIN 5/16" FLAT WASHER SLOT control rod. Insert the end of the flow control rod HANDLE GRIP FLOW CONTROL through the slot in the flow control mounting bracket and through the hole in the flow control link. Secure with a 3/32" x 3/4" cotter pin. See figure 9. 5/16" (LONG) NUT FLAT WASHERS FIGURE 11 1/4" x 1-3/4" HEX BOLT 1/4" NYLOCK HANDLE TUBE (SHORT) HANDLE TUBE MOUNTING BRACKET FIGURE 9 6 22. Place the adjustable stop into the "ON" end of the 23. Position the flow control mounting bracket (figure slot in the top of the flow control mounting bracket. 13). Secure with the 1/4" x 3/4" carriage bolt, a nylon a. Push on flow control arm until it locks in "OFF" washer, a 5/16" flat washer and the nylon wing nut. position. See figure 12. b. Slide flow control mounting bracket along tube until closure plate in bottom of hopper just closes. c. Snug the 1/4" lock nuts just enough to hold flow control mounting bracket in place. d. Set adjustable stop at "5". Pull flow control arm against stop. Verify that closure plate has opened about half way. e. If closure plate does not open half way, it may be closed too far at "OFF". Adjust position of flow control mounting bracket until closure plate will open about half way at "5" and still close when arm is locked in "OFF". Tighten 1/4" lock nuts. FIGURE 12 5/16" FLAT WASHER NYLON WASHER 1/4" x 3/4" CARRIAGE BOLT NYLON WING NUT ADJUSTABLE STOP OFF ON 1234 678910 5 FLOW CONTROL ARM ON OFF AJDUSTABLE STOP SETTING "5" FIGURE 13 7 24. Attach an angle stop bracket and a swivel bracket to the rear hole in the R.H. shield bracket using a 1/4" x 1" hex bolt, two 5/16" washers, a nylon washer and a 1/4" Nylock nut. Place the angle stop bracket on the inside and the swivel bracket on the outside. Tighten the locknut so that the swivel bracket can pivot freely. See figure 14. Repeat step on L.H. shield bracket. 25. Attach a swivel bracket to the front hole in the R.H. shield bracket using a 1/4" x 1" hex bolt, two 5/16" washers, a nylon washer and a 1/4" Nylock nut. Tighten the nut so that the swiv...