Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Hitch Tubes. See figure 1. 2. Assemble the R.H. Hitch Tube to the spreader frame tube using two 1/4" x 2" hex bolts and 1/4" nuts. Do not tighten yet. Repeat for L.H. Hitch Tube. See figure 1. 1/4" x 2" HEX BOLT1/4" NUTVINYL CAP FIGURE 3 6. Assemble the vinyl cap onto the Hitch Control Tube. See figure 4. 7. Assemble the Control Cable to the Hitch Control Tube using the carriage bolt and nylon wing nut. See figure 4. FIGURE 1 3. Assemble the Hitch Control Tube between the Hitch Tubes using two 1/4" x 1-3/4" hex bolts and 1/4" nuts. Tighten all bolts and nuts . See figure 2. CARRIAGE BOLTNYLONWING NUTVINYL CAP 1/4" NUT1/4" x 1-3/4" HEX BOLT FIGURE 4 FIGURE 2 OPERATION APPLICATION TIPS 1. This unit will cover a 4 to 8 foot wide area depending on the material used and the towing speed. 2. To avoid misses or striping, make each pass about 5 feet from the previous one so some overlapping of spread pattern does occur. 3. For easiest application, spread across the shortest edges of lawn first, making two "header" strips for a turning area, and then spreading between the header strips. See figure 6. 4. If lawn is odd shaped, spread a border around the edges and then spread between the border. See figure 6. 5. Keep wheel approximately 4 feet from any area you do not wish to spread. IMPORTANT: Be careful when using spreader around ornamental plants because weed control chemicals can damage these plants. HOW TO USE YOUR SPREADER ADJUSTING THE FLOW RATE SETTING 1. Loosen the wing nut that fastens the control to the handle. 2. Slide the Adjustable stop to the desired setting and retighten the wing nut. See figure 5. FLOW CONTROL LEVERADJUSTABLE STOP FIGURE 6 FIGURE 5 MAINTENANCE & STORAGE USING YOUR SPREADER 1. Check the material package and the Spreader Settings sheet included with your spreader for the proper spreader setting and application rate. 2. Before filling spreader, move the control lever to the "OFF" position. 3. Move spreader onto a flat surface - either a walk or a driveway - and fill. 4. Slide the Adjustable Stop to the desired setting. 5. Start the spreader in motion, then move the control lever forward against the adjustable stop to begin spreading. 6. Maximum towing speed - 3 M.P.H. NOTE: Always place control lever in the "OFF" position while filling spreader and when stopping or turning, to prevent release of excess fertilizer. CHECK FOR LOOSE FASTENERS 1. Make a thorough visual check of the Spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. LUBRICATION 1. Apply a few drops of oil to all moving parts. CLEANING 1. Always empty spreader after each use, storing leftover material in it's original bag. 2. Wash the spreader and dry thoroughly after each use. STORAGE 1. Empty and clean the hopper as instructed in maintenance section. 2. Store in a clean, dry area. INSTRUCCIONES PARA EL ARMADO 4. Coloque los Soportes de Enganche en el Tubo de Control de Enganche, usando dos pernos hexagonales de 1/4” x 1-3/4” y dos tuercas. Apriete pernos y tuercas. Vea la Figura 3. 5. Haga pasar el pasador de enganche a traves de los soportes de enganche y asegure con el pasador de horquilla de 1/8”. Vea la Figura 3. HERRAMIENTAS NECESARIAS PARA EL ARMADO (2) Llaves de 11 mm REMOCION DE LAS PIEZAS DE LA CAJA Saque todas las piezas y los paquetes de ferreteria de la caja. Extienda sobre una superficie todas las piezas y la ferreteria, e identifiquelas usando las ilustraciones de la pagina 3. TUERCAPERNO HEXAGONALDE 1/4" X 1-3/4" PASADOR DE ENGANCHEPASADOR DE HORQUILLA 1. Coloque las tapas de vinilo sobre los extremos de los Tubos de Enganche de Mano Derecha y de Mano Izquierda. Vea la Figura 1. 2. Coloque el Tubo de Enganche de Mano Derecha en el tubo del marco del esparcidor, usando dos pernos hexagonales de 1/4” x 2” y dos tuercas. No las apriete todavia. Repita la operacion con el Tubo de Enganche de Mano Izquierda. Vea la Figura 1. PERNO HEXAGONALDE 1/4" X 2" TUERCATAPA DE VINILO FIGURA 3 6. Coloque la tapa de vinilo en el Tubo de Control de Enganche. Vea la Figura 4. 7. Fije el Cable de Control ...