Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Stay off steep slopes! • Follow maintenance and lubrication instructions as outlined in this manual. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. ENGLISH ASSEMBLY INSTRUCTIONS 4. Assemble the four hitch braces in pairs to the inside of the hopper frame using a 1/4" x 1-3/4" hex bolt (B) and 1/4" nylock hex nut (F) on each side. DO NOT TIGHTEN YET. See figure 2. 5. Assemble the two OUTER hitch braces to the hitch tube using a 1/4" x 1-3/4" (B) hex bolt and a 1/4" nylock hex nut (F). DO NOT TIGHTEN YET. Do not assemble the inner hitch braces at this time. See figure 2. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (2) 7/16" Wrenches (2) 1/2" Wrenches (2) 9/16" Wrenches (B) 1/4" x 1-3/4" HEX BOLT(F) 1/4" NYLOCKHEX NUTHITCH BRACEOUTERHITCHTUBEHITCH BRACEOUTER REMOVAL OF PARTS FROM CARTON Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on pages 2 and 3. 1. Turn the spreader upside down as shown in figure 1. 2. Remove the lock nut from the middle bolt in the crossover tube and shaft support plate. Leave the bolt in place. See figure 1. 3. Assemble the hitch tube onto the middle bolt and secure it with the same lock nut you removed. DO NOT TIGHTEN YET. See figure 1. IMPORTANT: The hitch tube must attach to the side of the crossover tube opposite the shaft support plate. FIGURE 2 CROSSOVERTUBEHITCHTUBESHAFTSUPPORTPLATEMIDDLELOCK NUTMIDDLE BOLT 6. Assemble a spacer (P), a 3/4" flat washer (K), a wheel (air valve facing out) and another 3/4" flat washer (K) onto the end of the axle that has only the small hole. See figure 3. 7. Install a 1/8" x 1-1/2" cotter pin (M) into the hole in the axle. See figure 3. SMALL HOLE(P) SPACER(K) 3/4" FLATWASHER(M) 1/8" x 1-1/2" COTTER PINAIR VALVE FIGURE 1 FIGURE 3 ENGLISH 8. Assemble a spacer (P), a 3/4" flat washer (K), a wheel (air valve facing out) and another 3/4" flat washer (K) onto the end of the axle that has both the large and small holes. See figure 4. 9. Install a 1/8" x 1-1/2" cotter pin (M) into the small hole in the end of the axle. See figure 4. 10. Open the bail on the drive pin (V) and install it through the wheel and the large hole in the axle. Close the bail to lock the pin in place. See figure 4. 14. Assemble the two INNER hitch braces to the flow control mounting tube using a 1/4" x 1-3/4" hex bolt (B) and a 1/4" nylock hex nut (F). DO NOT TIGHTEN YET. See figure 6. 15. TIGHTEN all nuts and bolts assembled up to this point. Do not collapse the tubes when tightening. (B) 1/4" x 1-3/4" HEX BOLT(F) 1/4" NYLOCKHEX NUTHITCH BRACEINNERFLOW CONTROLMOUNTING TUBEHITCH BRACEINNER (V) DRIVE PINAIR VALVE(P) SPACER(K) 3/4" FLATWASHER(M) 1/8" x 1-1/2" COTTER PIN FIGURE 6 FIGURE 4 11. Turn the spreader upright on its wheels. 12. Assemble the flow control mounting tube to the hitch tube using two 5/16" x 1-3/4" hex bolts (A) and 5/16" nylock hex nuts (G). DO NOT TIGHTEN YET. See figure 5. 13. Assemble the vinyl cap (S) onto the flow control mounting tube. See figure 5. (G) 5/16" NYLOCKHEX NUT(A) 5/16" x 1-3/4" HEX BOLT(J) 5/16" FLATWASHEROFFON12346789105 16. Assemble the flow control mounting bracket to the flow control mounting tube using two 5/16" x 1-3/4" hex bolts (A), four 5/16" flat washers (J) and two 5/16" nylock hex nuts (G). DO NOT TIGHTEN YET. See figure 7. (A) 5/16" x 1-3/4" HEX BOLT(G) 5/16" NYLOCK HEX NUT(S) VINYL CAPFLOW CONTROLMOUNTING TUBE FIGURE 7 FIGURE 5 ENGLISH 17. Assemble the vinyl grip (T) onto the flow control arm. See figure 8. 18. Insert the flow control arm down through the slot in the flow control bracket. Assemble the small hole of the flow control link (U) to the flow control arm using a 1/4" x 1" hex bolt (D), a nylon washer (I) and a 1/4" nylock hex nut (F) as shown in figure 8. Tighten carefully. The flow control link should be snug but should pivot with no more than slight resistance. 20. Hook the double bent end of the flow control rod through the hole in the slide gate bracket located near the bottom of the hopper. See figure 10. (D) 1/4" x 1" HEX BOLT(F) 1/4" NYLOCKHEX NUTOFFON12346789105(U) FLOWCONTROLLINK(small hole) (I) NYLONWASHER(T) VINYL GRIP FIGURE 10 21. Place a 5/16" flat washer (J) onto the other end of the flow control rod. Insert the end of the rod through the curved slot in the flow control mounting bracket and through the hole in the flow control link. Secure with a 5/16" flat washer (J) and a 3/32" x 3/4" cotter pin (L). See figure 11. NOTE: You can leave off the second washer if there is not enough room on the end of the rod. (J) 5/16" FLATWASHER(L) 3/32" HAIRCOTTER PINFLOwCONTROLRODOFFON12346789105(J) 5/16" FLATWASHER FIGURE 8 OFFON12346789105(D) 1/4" x 1" HEX BOLT(F) 1/4" NYLOCKHEX NUT(I) NYLONWASHERS (2) 19. Assemble the flow control arm to the flow control mounting bracket using a 1/4" x 1" hex bolt (D), two nylon washers (I) and a 1/4" nylock hex nut (F). Tighten carefully...