Log:
Évaluations - 4, GPA: 3.8 ( )

Instructions McCulloch, Modèle CABRIO 95390044500

Fabricant : McCulloch
Taille : 764.33 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


WARNING: Please do not use the accessory nylon string head guard (item C Fig. 3 F) together with metal blades. G. ENGINE/SHAFT ASSEMBLY A DANGER. Do not run engine without shaft attached as clutch could fly off. 1) Insert the shaft (A) into the engine joint (B) making the female squared end (C) inside the joint mates with the male squared end (D) of the shaft. Rotate the shaft from right to left to obtain a precise fit. Now tighten the locking bolt (E) clockwise to ensure the shaft is held firmly in the joint. 2) If the joint is not tightened onto the engine housing, first make sure the shaft is fully and correctly engaged up to the shank, then tighten the 4 screws (A) in a criss-cross sequence. H. HANDLE ASSEMBLY 1) DOUBLE HANDLE Adjust and secure double handle clamp 40 cm from engine/shaft joint by tightening the screws(C). 2) DELTA FRONT HANDLE Secure the handle in front of the label placed on the shaft 11 cm from the rear grip when assembling nylon string head and 36 cm 3) Assemble the eyelet (A) of the ground wire onto the end of the throttle cable and install the washer (B). Insert the throttle cable into the cable mount (C), install the second washer (B) and insert the hexagonal nut. 4) Fit the end of the trigger cable connector (B) into the slot on swivel (C). 5) Adjust the nut (D) of the trigger cable connector so that the cable can easily slide in the opening with a play of 1 mm before operating the swivel (C). Tighten now the hexagonal nut (E). 6) Stop switch (STOP) cable: fit the connection. when assembling metallic blades. This position ensures optimum balance and safety. The handle must be perpendicular to the shaft as illustrated (Fig.2).The handle bar must be mounted using all the items supplied and in the exact configuration shown in figures 1 or 2. I. STARTING AND STOPPING THE ENGINE WARNING. First read sections: SAFETY RULES, SAFETY USAGE and SYMBOLS. COLD ENGINE STARTING 1) Move stop switch to the “ON” position. 2) Depress the safety lever (S), squeeze the accelerator trigger (A) and push the throttle advance forwards (B). Now release the accelerator trigger (A) and then the throttle advance (B). WARNING: when the throttle advance is engaged, the head or blade rotates. 3) Move choke lever (E) to the closed position . 4) Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope until engine fires once. 5) Move choke lever (E) to the open position then pull starter rope until engine fires. Let engine run for a few seconds holding the trimmer. Now disengage throttle advance by pulling trigger completely. Engine will now keep on running at idle speed. HOT ENGINE STARTING STOP switch on START position I. Trigger on idle position (released). Choke towards (open position ). Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope. WARNING: when the throttle (B) advance is engaged, the head or blade rotates. 6) ENGINE STOPPING Press the stop switch moving it to STOP position 0. WARNING: when the engine is switched off rotating parts, blade or nylon string head, will keep on rotating for a few seconds. Hold the machine until all parts come to a standstill. N.B. In an emergency the above mentioned delay in stopping may be shortened by touching blade parallel on the ground. A L. CARBURETTOR ADJUSTMENT Your machine may be fitted with a highly sensitive low emission carburettor. We now therefore recommend that carburettor adjustments are only made by an authorised servicing dealer, equipped with instruments that will ensure best performance with lowest emission levels. To adjust the idle speed, however, proceed as follows: With engine running and warm, slowly turn screw ‘I’ or ‘T’ clockwise until the engine runs smoothly with a consistent noise level but without making the chain or cutting head rotate. If the cutting attachment does move or the engine runs too fast, slowly turn screw ‘I’ or ‘T’ in an M. REGULAR MAINTENANCE From time to time ensure all screws are tight. Replace damaged, worn, cracked or warped blades. Always make sure nylon string head or blade have been assembled correctly (see sections NYLON STRING HEAD and BLADE ASSEMBLY) and blade fastener is tightened. 1) AIR FILTER CLEANING (at least every 25 working hours). A dust cl...

Ce manuel est également adapté pour les modèles :
Outils de jardin - CABRIO 251 / 25 cc (764.33 kb)
Outils de jardin - CABRIO 261 / 25 cc (764.33 kb)
Outils de jardin - CABRIO 262 / 25 cc (764.33 kb)
Outils de jardin - CABRIO 290 / 29 cc (764.33 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories