Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
WARNING 1. Select bare ground for fueling. 2. Move at least 10 feet (3 meters) away from the fueling point before starting the engine. 3. Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container. ¦ FOR YOUR ENGINE LIFE, AVOID: 1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly. 2. GASOHOL – It can cause deterioration of rubber and/ or plastic parts and disruption of engine lubrication. 3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking. 4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly. 5. In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel. 6. In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site. NOTE As for details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to the mixed gasoline, etc. described therein, it may not be covered by the warranty. G B Pay attention to agitation. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. GB-9 BC2604DL / BC2604DW 8. Operation STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine. 3. Push the primer pump several times until overflown fuel flows out in the clear tube. (1) choke lever (2) close (3) open (4) primer pump 4. Move the choke lever to the closed position. 5. Set the ignition switch to the “I” position. Set the throttle lever to the start position (1 > 2 > 3). Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. 3. Ignition switch BC2604DL BC2604DW 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. START O : Stop I : Start WARNING The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts. IMPORTANT • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 7. Move the choke lever downward to open the choke. And restart engine. 8. Allow the engine to warm up for a several minutes before starting operation. NOTE 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. STOPPING ENGINE O : Stop I : Start 3. Ignition switch BC2604DL BC2604DW 1. Release the throttle lever and run the engine for half a minute. 2. Shift the ignition switch to the STOP position. IMPORTANT • Except for an emergency, avoid stopping the engine while pulling the throttle lever. GB-10 BC2604DL / BC2604DW 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster as required. G B (1) .04 in (1 ~ 2 mm) METAL BLADE USAGE 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fastened according to instruction and the blade turns smoothly without abnormal noise. (1) Cable adjuster ADJUSTING IDLING SPEED (1) Idle adjusting screw 1. When the engine tends to stop frequently at idling mode, turn the adjusting screw clockwise. 2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise. NOTE •Warm up the engine before adjusting the idling speed. CUTTER APPLICATION CHART • Replace by a suitable recommended cutting attachment according to the object to be cut. • When replacing blade always be sure to use products which have been certified by ZENOAH. WARNING • The rotating parts fastened incorrectly may cause serious accident to the operator. • Make sure that the blade is not bent, warped, cracked, broken or damaged. • If you find any error to the blade, discard it ...
Ce manuel est également adapté pour les modèles :Outils de jardin - BC2604DL (796.66 kb)