Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
MOUNTING OF PROTECTOR To meet the applicable safety provisions, only the tool/protector combinations as described in the table must be used. Use genuine DOLMAR cutter blades or nylon cutting head. The cutter blade must be well sharpened, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately. MS-260 U/261 U MS-330 U/331 U MS-230 C/231 C MS-260 C/261 C MS-330 C/331 C to Engine 20 Star Blade Eddy Blade Protector for metal blades Nylon cutting head Protector for cord cutter Sharpen or replace the cutter blade every three (3) hours of operation. If the nylon cutting head hits against a stone during operation, stop the engine and check the nylon cutting head immediately. CAUTION: The appropriate blade guard must always be installed for your own safety and complying with accident-prevention regulations. Operation without the safety guard is not permitted. 8 For # MS-260 U/261 U and # MS-330 U/331 U Fix the protector (1) to the clamp (3) with two bolts. For # MS-230 C/231 C, MS-260 C/261 C and MS-330 C/331 C Fix the protector (1) to the clamp (3) with two bolts. (1) (3) (3) (1) MOUNTING OF CUTTER BLADE OR NYLON CUTTER HEAD Turn the Brush Cutter/String Trimmer upside down and replace the cutter blade or the nylon cutting head. -Installing Cutter-Blade Mount the cutter blade (A) onto the receiver washer (B). Make sure that the cutter blade (A) is centered and lies flat. The guide of the receiver washer (B) must fit in the arbor hole in the cutter blade (A). Install the clamp washer (C) with the raised center away from the cutter blade (A). Insert the holding-pin (D) through the slot of the grass cover (E) and rotate the receiver washer (B) until it is locked with the holding -pin (D). Then install the nut guard (F) and the blade nut (G) onto the gear case and turn counterclockwise to tighten securely. Note : Always wear gloves when handling the cutter blade -Installing Nylon cutting head Install the receiver washer (A) onto the gear case. Insert the holding-pin (B) through the slot of the grass cover (C) and rotate the receiver washer (A) until it is locked with the holding-pin (B). Then place the nylon-cutting head (D) on the receiver washer (A) and rotate the nylon-cutting head (D) counterclockwise to tighten securely. STOP ABDCFGECBAD 9 FUELS/REFUELING Handling fuel Utmost care required when handling fuel. Fuel may contain substances similar to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel vapors, avoid any contact of fuel or oil with your skin. Mineral oil products degrease you skin. If your skin contacts with these substances repeatedly and for an extended period of time, it will desiccate. Various skin diseases may result. In addition, allergic reactions may occur. Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately wash them with clear water. If your eyes are still irritated, see a doctor immediately. STOP Fuel and oil mixture This brush-cutter (string-trimmer) is powered by a high-efficiency two-stroke engine being run with a mixture of fuel Observe the Safety Instructions and two-stroke engine oil. The engine is designed for unleaded gasoline intended for automotive use with an on page 6. octane rating of 87 or higher. For lubricating the engine, use any brand of premium 2-stroke engine oil classified as grade ISO-L-EGD or JSAOFC to be added to the fuel. Using any other oil will shorten the engine life and increase the required maintenance. It is absolutely required to observe a mixture ratio of 50 : 1 (2-stroke engine oil specified above), unless otherwise reliable function of the brush cutter ( or string trimmer ) cannot be guaranteed. Correct Fuel Mixture ( 50 : 1 ) Gasoline Oil 1 Gallon (US) 2.6 oz. 1 Liter 20 cc ( 20ml ) 5 Liter 100cc ( 100ml ) Note : When doing the fuel-oil mixture, first mix the entire oil quantity with half of the fuel required, then add the remaining fuel. Before filling it into the brush-cutter ( string trimmer ) tank, thoroughly shake the mixture. It is not recommended to add more engine oil than specified to ensure safe operation. This will result in a higher production of combustion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the muffler. In addition, the fuel consumption will rise and the performance will decrease. Refuelling Follow the appropriate manners described on page 6. Storage of Fuel Fuel ca...
Ce manuel est également adapté pour les modèles :Outils de jardin - MS-231 C (1.32 mb)
Outils de jardin - MS-260 C (1.32 mb)
Outils de jardin - MS-260 U (1.32 mb)
Outils de jardin - MS-261 C (1.32 mb)