Évaluations - 4, GPA: 4 ( )

Fabricant : Husqvarna Taille : 1.47 mb Nom Fichier : Langue d'enseignement:

otection for transport blade when the machine is in the resting position for transport or storage. Safety guard 1 2 3 4 10 This very important safety device (fig. A no.19) prevents any objects that come into contact with the cutting device, or the grass itself, from flying up and striking the operator. Safety pole guard 1 2 3 4 This device, fastened to the machine, ensures a minimum distance between the operator and the cutting device during use, and prevents the machine from striking and injuring the operator if the blade hits a hard surface (fig. A no. 20). Muffler 1 2 3 4 6 7 9 14 The muffler serves to reduce the noise level to a minimum and to route the exhaust fumes produced by the combustion engine away from the operator. The guard covers the sharp extremities of the ENGLISH - 4 Harness CAUTION! It is very important to famil-The harness is equipped with a fasten-release iarize yourself with the release mecha-mechanism. The harness enables the operator to nism. In case of emergency you need to be support the machine during use (see “Safety pre- able to release the machine quickly. cautions”, B7). D. Fuel Mixture Preparation of the mixture 7 14 15 Do not use any other type of fuel than the type recommended in this manual. This tions indicated in the table on the cover, fig. D. engines that use unleaded gasoline in the propor- = 90) and fully synthetic oil specific for two-speed unleaded gasoline (with a minimum octane rating and should therefore be fueled with a mixture of machine is equipped with a two-stroke engine Control the specifications of the oil shown on the package; the use of oil lacking the specifications expressly indicated in this manual could cause serious damage to the engine! To obtain the best mixture, pour the oil into an approved container first, followed by the gasoline, and shake the container well (every time you take fuel out of it). The characteristics of the mixture tend to deteriorate in time, so you should only prepare as much mixture as you are going to need (the use of deteriorated fuel can seriously damage the engine). Filling the tank 14 15 Clean the area around the fuel cap before removing it, to prevent any impurities from contaminating the fuel. Take the cap off the fuel container carefully. Unscrew the cap on the fuel tank and fill it with the necessary quality, using a funnel. During use, to prevent problems in starting the engine again, we strongly recommend that you avoid letting the fuel run out in the tank. Fuel storage 14 15 Store the fuel in a cool, well-ventilated place, in an approved fuel storage container. Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. Never store excessive quantities of fuel. E. Assembly/disassembly E1. Delta grip For your safety the label placed on the shaft at a distance of at least 18 cm fr be fastened in a comfortable working position. The safety pole guar the accessories supplied and in the configura- tion shown in the figur handle. E2. Double Handle Adjust and secur ing the scr E3. Assembly of safety guar Fit the safety guar position the lower clamp ( the shield and the upper clamp ( Insert and tighten the screws (H). . steps: Safety guard extension (exclusively for use with nylon string head) • The extension (B) should be installed only for use with the nylon string head, with the aid of the string cutter blade (L), that regulates the length of the string and thus the cutting diame• For correct assembly see the illustration on the cover and perform the following sequence of • Insert the extension (B) on the safety guard (A) at the reference notches (C), and fasten with the screws (D), then apply the string cutter blade (L) with the cutting edge facing towards the outside of the shield, and fasten it with the screw (E) (Make sure the screws are tightened all the way (E) and are not loosened by the vibrations. If necessary, tighten them again). CAUTION! If you are using the grass cutting blade, remove the extension (B) on the guard (A). ENGLISH - 5 E4. Assembly/disassembly of line cutter head Apply the nylon string head as shown in the illus- tration: 1) Upper plate 2) Protection (not supplied with all models) 3)Nylon string head. Tighten by ning counterclockwise. As you tighten, hold the nylon string head and plate still and insert theench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match. E5. Assembly/disassembly of grass cutterblade plate e) Fixed cup f) Blade fastening nut. ing and direction arrow facing upward d) Lower (not supplied with all models) c) Blade with word- Upper plate with blade centering b) Protection Apply the blade as shown in the illustration: a) CAUTION! Do not use the nylon string head guard extension with metal blades. 2 3 4 10 2 3 4 10 E6. Attachments fitting/removal (for split shaft mo...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :