Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Pull each string so that about 15 cm comes out on each side. Reassemble the nylon string head as shown. If the reel becomes excessively worn, replace it with a whole new reel. H3. Attachments maintenance Follow maintenance instructions on the attachment manual. I. Techniques for use 1 4 5 6 7 8 9 speed as running it at top speed without a load can damage the engine severely. The machine is ideal to complete the work of the cutting stage, decelerate the engine to minimum lawnmover. In fact, it can reach places where a Cutting techniques engine running at high speed. After every 10 11 12 13 14 16 17 Wait until the engine is running at minimum speed before moving the machine from one section to another. ENGLISH - 7 normal lawnmower is unable to go. Cutting and trimming grass borders with the nylon string head Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees. Mowing To prevent damage to your lawn or the cutting mechanism, keep the string parallel to the ground but avoid contact with the terrain. Trimming borders Angle the nylon string head keeping it a short distance from the ground. Cut using the end of the string. Do not press the string against the material to be cut. I1. Drawing out the string During cutting, the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: release the throttle trigger to reduce the engine speed to less than 8000 rpm. Tap gently on the ground with the button (A) as shown in the figure and the string will come out automatically. Accelerate again. If the string does not come out make sure there is still some left and try again. I2. Thinning grass with the grass cutter blade 2 16 The grass is cut with swinging motions from side to side, maintaining the blade parallel to the ground. During the right to left swing the grass is cut, while the backswing must be made without using the blade. KICKBACK can occur when cutting is done with the risk sector of the blade; we recommend cutting with the rest of the blade. Take care that the cup supporting the blade just grazes the ground. This will prevent the blade from touching the ground. L. Environmental information This section contains information useful for maintaining the characteristics of eco-compatibility included in the origin design of the machine, and as regards proper use and disposal of oil and fuel. Design In the design stage, care was taken to develop an engine with reduced consumption and low emissions of noise and pollutant exhaust fumes. Use of machine The operations of filling the tank with the fuel mix ture should be carried out in such a way as to avoid spilling fuel and contaminating the soil and environment. Periods of prolonged disuse Always empty the fuel tank with the same precautions used in filling it. Disposal Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized organization for proper disposal in compliance with the regulations in force. M. Troubleshooting table Engine will not start Engine runs badlyor looses powerwhen cutting The machine runs but does not cut well Check STOP switch is in the position I. • Control fuel level min. 25%tank capacity. • • Check air filter is clean. • • Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. • • Change fuel filter. Contact your dealer. • Carefully follow the cutting accessory assembly instructions. • Check metal cutting accessory is sharp. Otherwise, contact your dealer. • The engine continues to have problems: contact your authorized supplier ENGLISH - 8 N. Declaration of conformity The undersigned, authorized by Husqvarna Outdoor Products Italia SpA, declares that the following products model /TYPE: BC022, BC010C, BC040 starting from the serial numbers produced from 2005 on, manufactured by Husqvarna Outdoor Products Italia SpA, Valmadrera, Italia, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/EEC (Electromagnetic Compatibility Directive), directive 2000/14/EEC (Enclosure V). Valmadrera, 10.11.06 Giuseppe Todero (Technical Manager) Husqvarna Outdoor Products Italia SpA Via Como 72, 23868 Valmadrera (Lecco) ITALY O. Technical data Displacement (cm3) .............................................................................................................. Bore (mm) ............................................................................................................................. Stroke (mm) .......................................................................................................................... Engine output (kW) (ISO 8893) .............................................................................................. Maximum shaft rotation frequency (min-1) .......................................................
Ce manuel est également adapté pour les modèles :Outils de jardin - 249953 (1.08 mb)
Outils de jardin - 953900739 (1.08 mb)