Évaluations - , GPA: ( )

Instructions Husqvarna, Modèle 966043501

Fabricant : Husqvarna
Taille : 1006.66 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

RATESETTINGCONVERSIONRATESETTINGCONVERSIONRATESETTINGCONVERSIONRATESETTINGCONVERSION 70PP Setting B C D E F G H I J K L M N O P Q R S T U V W X Y Z PrizelawnPrizelawnPrizelawnPrizelawn®®®® BFBFBFBFllll\CBR\CBR\CBR\CBR Setting B C D E F G H I J K L M N O P Q R S T U V W X Y Z PrizelawnPrizelawnPrizelawnPrizelawn®®®® CBRII Setting — 2 — 2.5 — 3 3.5 — 4 — 4.5 5 5.5 6 6.5 7 8 9.5 10 11 12 13 14 15 — Lesco #029600 Setting — B C D — E F — G H I — J K L — M N O — P Q R — S Scotts R8A/SR-1 Setting D E F G H I J K L M N O P Q R S T U — V W — X Y Z Earthway 2200/2400 Setting 5 — — — 10 — — — — 15 — — — — 20 — — — — 25 — — — — 30 Spyker 76/78-2 Setting — 3 — — — 4 — — 5 — — 6 — — 7 — — 8 — — — 9 — — 10 Scotts SPEEDY GREEN — — — 2 — — 3 3.5 J 4.5 5 5.5 6 — 6.5 — 7 — 7.5 — 8 — 8.5 — 9 5 The following provides approximate 70 PP settings when only the product weight, square foot coverage, and visual inspection of the material is available. FERTILIZER PARTICLE SIZE BAG RATE Lbs. of fertilizer used per 1,000 sq. ft. of coverage APPROX. SETTING SPREAD WIDTH Large, heavy particles 5 10 15 M O Q 12 12 12 Medium-mixed particles 5 10 15 L N O 10 10 10 Small particles (nitrogen) 1 2 3 G J L 10 10 10 Mixed size particles -some fines 5 10 15 M O P 8 8 8 Light weight particles 5 10 15 J L O 6 To 8 The conversions should be used as guidelines for establishing proper rate settings for the particular product being applied. Steps for obtaining the most accurate settings are outlined in the “How to Determine Spreader Settings and Spread Width” section of this manual. These settings are approximate and may vary due to physical characteristics of the product. Walking speed, wear, condition of the turf and humidity, may cause actual rate setting to deviate. No expressed nor implied warranty or guarantee is provided as to coverage or uniformity indicated by these rate settings. M MMMM A AAAA I IIII N NNNN T TTTT E EEEE N NNNN A AAAA N NNNN C CCCC E EEEE 1. Never store unused material in spreader. Return unused product to its original container. 2. Wash spreader thoroughly after each use and dry completely in sun or heated area. 3. Grease axle bearings in frame. Oil the impeller shaft bearing in hopper, pivot points on the shut-off plate and the spring in the housing behind the rate plate. 4. Remove gear cover and wash gears thoroughly. Oil all bearing areas and face of gear teeth. Lubricate gear teeth and re-install gear cover. 5. Gear mesh should be checked on a regular basis during high use periods. Clearance between the axle gear and pinion gear should be minimal but not tight. If adjustment is necessary, loosen axle collar set screw and hold gears together. Slide axle collar against the gear support and tighten axle collar set screw. Spin drive wheel. Gears should run freely and smoothly. 6. Impeller surface should be cleaned periodically to remove build-up of product. Build-up can cause the spread pattern to change. 7. Tire pressure should be 20-25 PSI. Grease Oil Bearing In Hopper Axle Collar Oil Oil 6 CALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONSCALIBRATIONINSTRUCTIONS The spreader was factory calibrated, however, calibration should be checked occasionally to assure optimum performance. 1. Pull the on/off lever to the “OFF” position. Set the rate control plate to setting “B”. Pointer Pointer Screw Rate Control Knob Rate Control Plate MODEL 70 PP 2. Flip on/off control lever to the “ON” position. Check the port opening. It should be just open. If adjustment is necessary, continue to step #3. 3. Loosen the rate control knob and slide the rate plate until the port is just opening. Loosen pointer screw and move pointer until it aligns with “B” on the rate plate. Retighten pointer screw. VIEW IS INSIDE OF HOPPER Port is just open NOTESNOTESNOTESNOTES 7 Key No. Description Part No. Key No. Description PART NO. 1 Hopper Assembly 525 56 82-01 19 Discharge Chute Knob (2 Req.)* 525 56 83-02 1A Hopper* 525 56 82-02 20A Shutoff Plate Guide-RH.* 525 56 83-05 2 Frame Assembly 525 56 92-01 20B Shutoff Plate Guide-LH.* 525 56 83-04 3 Axle Bearing (4 Req.) 525 56 86-03 21 Shutoff Plate* 525 56 84-01 4 Axle 525 56 86-01 22 Hopper Cover 525 56 82-04 5 Gear Cover Clamp (3 Req.) 525 56 88-02 23 Fastener Package 525 56 94-01 6 Gear Cover Assembly 525 56 88-01 24 Control Tube 525 56 89-01 7 Impeller Shaft 525 56 87-03 25 Upper Handle 525 56 85-03 8 Axle Gear 525 56 86-04 26 Handle Grip (2 Req.) 525 56 85-02 9 Agitator 525 56 00-02 27 Handle Lever Ass’y w/Chain 525 56 85-01 10 Impeller Shaft Bearing* 525 56 87-02 28 Handle Brace 525 56 85-04 11 Axle Collar w/ Scr. (3 Req.) 525 56 86-02 29 Hopper Label 525 56 82-05 12 Pinion Gear 525 56 88-04 30 Hopper Screen 525 56 82-03 13 Gear Support 525 56 88-03 31 Leg 525 56 98-01 14 Impeller 525 56 87-04 32 Rate Plate* 525 56 84-02 15 Drive & Free Turning Wheel 525 56 96-02 33 Rate Control Knob* 525 56 93...