Évaluations - 4, GPA: 4.3 ( )

Fabricant : Ryobi Taille : 6.65 mb Nom Fichier : Langue d'enseignement:

CUTTING TIPS See Figures 16 -17. . Avoid hot surfaces by always keeping the tool away from your body. (Proper operating position shown in figure 15.) . Keep the trimmer tilted toward the area being cut; this is the best cutting area. . The curved shaft trimmer cuts when passing the unit from right to left. The straight shaft trimmer cuts when passing the unit from left to right. This will avoid throwing debris at the operator. Avoid cutting in the dangerous area shown in illustration. . Use the tip of string to do the cutting; do not force string head into uncut grass. . Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, curbs, and wood may wear string rapidly. . Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be damaged by the string. GRASS DEFLECTOR LINE TRIMMING CUT-OFF BLADE See Figure 18. The trimmer is equipped with a line trimming cut-off blade on the grass deflector. For best cutting, advance string until it is trimmed to length by the cut-off blade. Advance the BEST CUTTING AREA DANGEROUS CUTTING AREA Fig. 17 direction of rotatio n DANGEROUS CUTTING AREA Fig. 16 BEST CUTTING AREA Fig. 18 straight shaft trimmer LINE TRIMMING CUT-OFF BLADE Curved shaft trimmer LINE TRIMMING CUT-OFF BLADE direction of rotatio n straight shaft trimmer curved shaft trimmer OPERATION string whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep the string long enough to advance properly. 19 . Inspect and clear the area of any hidden objects such as glass, rocks, concrete, fencing, wire, wood, metal, etc. . Never use blades near sidewalks, fencing, posts, buildings or other immovable objects. . Never use a blade after hitting a hard object without first inspecting it for damage. Do not use if any damage is detected. . The unit is used as a scythe, cutting from the right to the left in a broad sweeping action from side to side. . Use only the Tri-Arc® blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury. OPERATING THE BRUSHCUTTER See Figures 19 - 20. Hold the brushcutter with your right hand on the rear handle and the your hand on the “J” handle. Keep a firm grip with both hands while in operation. Brushcutter should be held at a comfortable position with the rear handle about hip height. Maintain your grip and balance on both feet. Position yourself so that you will not be drawn off balance by the kickback reaction of the cutting blade. Adjust the shoulder harness to position the brushcutter at a comfortable operating position and to assure that the shoulder harness will reduce the risk of operator contact with the blade. BLADE THRUST Exercise extreme caution when using the blade with this unit. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut with the brushcutter from the right to the left. In the event an unexpected object or woody stock is encountered, this practice could minimize the blade thrust reaction. WARNING: To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. Tri-Arc® BLADE The Tri-Arc® blade is suited only for thicker weeds and pulpy stalks. When the blade becomes dull, it can be turned over to extend the life of the blade. Do not sharpen the Tri-Arc® blade. CUTTING TECHNIQUE - BLADE WARNING: Extreme care must be taken when using blades to ensure safe operation. Read the safety information for safe operation using the blade, refer to Specific Safety Rules for Brushcutter and Blade Use earlier in this manual. . Always hold brushcutter on your right side with both hands when operating. Use a firm grip on both handles. . Maintain your grip and balance on both feet. Position yourself so that you will not be drawn off balance by the kickback reaction of the cutting blade. OPERATION Fig. 19 direction of rotatio n cutting area Fig. 20 proper operati ng position 20 OPERATION STARTING AND STOPPING See Figures 21 - 23. To start a cold engine: DO NOT squeeze the throttle trigger until the engine starts and runs. . Lay the trimmer on a flat, bare surface. . PRIME - Press the primer bulb 7 times. . SET the start lever to the START position. . PULL the rope until the engine starts. . Wait 6-10 seconds, then squeeze the trigger to run. NOTE: Squeezing and releasing the throttle trigger releases the start lever to the RUN position. To start a warm engine: PULL the rope until the eng...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :