Évaluations - 5, GPA: 3.6
(
)
)
|
Facilité d'utilisation
Do not operate the unitif the cutting attachmentshield is missing, loose, Always make sure or broken. the appropriate 15 METERScutting attachment (50 FEET) shield is correctlyBe extremely careful installed. Beware of a coastingof slippery terrain, blade when brushcutting orespecially during rainy edging. A coasting blade weather. can injure while it continuesto spin after the throttletrigger is released or afterthe engine is stopped. Be constantly alert forobjects and debris that ALWAYS clear your work area ofcould be thrown either trash or hidden debris that could from the rotating cutting be thrown back at you or towardattachment or bounced a bystander. When operating in from a hard surface. rocky terrain or near electric wiresor fences, use extreme caution to If contact is made with a hard object, avoid contacting such items with stop the engine and inspect the cutting the cutting attachment. attachment for damage. Product Description Using the illustration as a guide, familiarize yourself with your machine and its various com- ponents. Understanding your machine helps ensure top perfor- mance, long service life and safer operation. WARNING! Do not make unauthorized modifications or alterations to any of these units or their components. Outer Tube Grip Cutting Attachment Shield Gearcase Handle Throttle Trigger Throttle Interlock IgnitionSwitch Fuel Tank Hanger Throttle Lock Button Shoulder Strap Hip Pad Specifications Engine Name C254 Engine Type 4-cycle, vertical cylinder, air cooled Dry Weight (Without guard and strap) 6.1 kg/14.1 lb. Bore x Stroke 34 x 27 mm / 1.3 x 1.1 in. Displacement 24.5 cc/1.5 cu. in. Fuel/Oil Ratio 50:1 with *ISO-L-EGD or JASO FD class engine oil Fuel Tank Capacity 590 ml/20.0 oz. Carburetor Type Diaphragm-type Ignition One-piece electronic, program-controlled Spark Plug** NGK CMR5H Plug Gap 0.6 mm / 0.024 inch Torque 16.7 - 18.6 N•m / 148 -165 in • lbs Air Cleaner Type Foam pre-filter; sealed felt main filter Starting Method Recoil Stopping Method Slide switch Transmission Type Automatic, centrifugal clutch w/bevel gear Engine Idle Speed 3,000 RPM Clutch Engagement Speed 4,100 RPM Wide Open Throttle Speed (W.O.T.) 10,500 RPM Specifications are subject to change without notice. Emission Control (Exhaust & Evaporative) EPA 2010 and Later and/or C.A.R.B. TIER III The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to California models only. An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY; information on label varies by engine FAMILY). PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD) The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. Assembly This unit comes fully assembled with the exception of the handlebar, cutting attachment shield and cutting attachment. IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation. Handlebar Assembly Install the handlebar: 1. Remove four (4) upper cap retaining screws, and remove upper cap from handlebar mounting bracket. 2. Place handlebar on mounting bracket, and secure with upper cap and four (4) screws. 3. Adjust handlebar position for best operator comfort and control, then tighten upper and lower cap retaining screws securely. 4. Secure cable to outer tube with two (2) bands provided. Prior to Assembly Before assembling, make sure you have all the components required for a complete unit and inspect unit and components for any damage. ¦ Engine/Outer tube assembly ¦ Handlebar and Throttle assembly ¦ Cutting attachment shields ¦ Cutting Attachment ¦ Shoulder Strap w/Hip Pad ¦ Cutting attachment shield mounting brackets and assembly hardware ¦ Cutting attachment adapter plates ¦ 4 mm hex key wrench (Also use as a locking tool) ¦ T-wrench Outer tube Lower capretaining screws Handlebar Ignition switch Throttle trigger Hanger Mounting the brushcutter handlebar Handle positioninglabel Bands Throttle lock button Throttle interlock Throttle Assembly Upper capretaining screws Upper cap Lower cap Handle bar Cutting attachment shield Tools Required: Screwdriver Parts Required: Plastic debris shield, shield plate, (3) 5 x 10 mm screws A C D C D E CAUTION Wear Gloves or personal injury may result: • Cutoff knife is sharp. • Gearcase and surrounding area may be hot. NOTE: The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades. 1. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO shaft (A). 2. Place the shield on the bottom of the bear...
Ce manuel est également adapté pour les modèles :Outils de jardin - C254 (1.52 mb)
Outils de jardin - C254 (1.52 mb)
Outils de jardin - C254 (1.52 mb)
Outils de jardin - C254 (1.52 mb)