|
Facilité d'utilisation
(2) Wear head, eye and ear protection. (3) Wear foot protection. (4) Wear gloves. (5) Beware of thrown objects. (6) Warning / Attention (7) Keep all children, bystanders and helpers 15 meters away from the machine. Explanation of pictorials ZENOAH CO., LTD. 12.Keep firm footholds and balance at all times. Do not use the unit where footing is unsteady or slippery. 13.Keep cutting attachment below waist level. 14.Keep all parts of your body away from the rotating cutting attachment and hot surfaces. 15.Warn the operator of the danger of blade thrust. (Kick back) Blade thrust may occur when the spinning blade contacts a solid object in the critical area. A dangerous reaction may occur causing the entire unit and operator to be thrust violently. This reaction is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury. Kick back is more likely to occur in areas where it is difficult to see the material to be cut. 16.When inspecting or servicing the unit, make sure to stop the engine and disconnect the spark plug as necessary. 17.Cover the blade when the transporting or storing the unit. Secure the unit before for storage or transporting to prevent loss of fuel, damage or injury. 18.When replacing cutting attachment or other components, be sure to use the parts supplied or recommended by ZENOAH. 19.When the unit is turned off, make sure the cutting attachment has stopped before the unit is set down. 20.For units equipped with a clutch, be sure the cutting attachment stops turning when the engine idles. 21.Use only for tasks explained in the instruction handbook. 22.Discard blades that are bent, warped, cracked, broken or damaged in any way. 23.Instructions on stopping a coasting blade. A blade can injure while it continues to spin after the engine is stopped or throttle control is released. 24. Stop the engine and blade before removing material that is blocking or entangling the cutting attachment. 25. Use a sharp blade. A dull blade is more likely to snag and thrust. Replace the fastening nut according to the manufacturer's instruction. 26. Cut only material recommended by the manufacturer. Do not let the blade contact material it cannot cut, such as rocks, metal etc. 27. Always wear safety boots, additionally a helmet is required if there is a risk of contact with falling objects. Thank you for purchasing a ZENOAH product. Before using our brushcutter, please read this manual carefully to understand the proper use of your unit. 1-9 Minamidai, Kawagoe, Saitama, 350-1165 Japan BRUSHCUTTERS BC2311LE BC2611LE/WE BC3501LE/WE BC4501WE If warning label peels off or becomes soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). IMPORTANT Never modify your machine. We won’t warrant the machine, if you use the remodeled brushcutter or if you don’t observe the proper usage written in the manual. WARNING ¦ ENGINE [BC2311LE/BC2611LE/WE] 1. Loosen the bolts temporarily attached to the clutch housing. 2. Push the drivershaft toward the gearcase and rotate it by hand to check that the driveshaft is engaged with the gears. 3. Insert the shaft tube into the clutch housing until it bottoms. When difficult to engage, twist the engine slightly. 4. Align the positioning holes on the clutch housing and the shaft tube and fit the bolt into the holes. And fasten the tightning bolts by turns securely. (Tightning torque: 4.9~7.8N.m. (0.5~0.8kgm)) (1) Positioning hole (2) Bolt (M5x10) (3) Tightning bolt (M5x22) 3 Setup ¦ INSTALLING BLADE Remove the guard skirt of debris guard, when using metal blade. 1. Put the angled bar(1) into the side holes of the inner holder and the gearcase. 2. Remove the nut(Left-handed) and the outer holder(3) from the gearshaft. 3. Put the blade onto the inner holder(2). Make the marked side face the holder. 4. Put the outer holder(3) onto the gearshaft making the recessed side face the blade. 5. Fasten the blade by the nut and the cover(4). ¦ BALANCE UNIT 1. Put on strap and attach unit to strap. 2. Slide clamp up or down until unit balances with head aparting from the ground when using it. • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) • Do not use BIA or TCW (2-stroke water-cooling type) mixed oil. • Exhaust emission are controlled by the fundamental engine parameters and components (eq., carburation, ignition timing and port timing) without addition of...
Ce manuel est également adapté pour les modèles :Outils de jardin - BC2611LE/WE (278.88 kb)
Outils de jardin - BC3501LE/WE (278.88 kb)
Outils de jardin - BC2311LE, BC2611LE, BC2611WE, BC3501LE, BC3501WE, BC4501WE (278.88 kb)