Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
shaft S Handlebar mounting bracket for 7/8. shaft S Bracket cover (2) S Shoulder strap S Upper shoulder strap clamp S Lower shoulder strap clamp (with spacer tabs) S Handlebar bracket screws (4) S Shoulder strap clamp screws (2) S 4- --point weed blade (assembled on brush- cutter attachment) S Large nut for installing blade S Retaining washer S Cupped washer S Metal shield (assembled on brushcutter at tachment) S Trimmer head S Plastic shield S Wing nut (screwed onto plastic shield) S Attachment hanger S Hex wrench WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use damaged parts. NOTE: If you need assistance or find that parts are missing or damaged, call 1-800-554-6723. TOOLS REQUIRED S Hex wrench (provided) INSTALLING BRUSHCUTTER ATTACHMENT CAUTION: When removing or installing at tachments, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Coupler LOOSEN TIGHTEN Knob 2. Remove the shaft cap from the brushcutter attachment (if present). 3. Position locking/release button of attachment into guide recess of coupler. 4. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 5. Before using the unit, tighten the knob securely by turning clockwise. Coupler Primary Hole Locking/ GuideRecessUpper Lower Release Shaft Attachment Button WARNING: Make sure the locking/release button is locked in the primary hole and the knob is securely tightened before operating the unit. HANDLEBAR ASSEMBLY DANGER: RISK OF CUT. To avoid se rious injury, the barrier portion of the handle bar must be installed as shown on the upper shaft of the powerhead to provide a barrier be tween operator and the spinning blade. Attach handlebar mounting bracket above arrow on safety warning decal on the upper shaft (pow erhead end of unit). Ensure handlebar is posi tioned on mounting bracket at the end of the arrow on the handlebar decal. NOTE: Two mounting brackets are included with this attachment. Both brackets are provided to adapt this attachment for use with power- heads that have either a 1. (2.5 cm) diameter or a7/8. (2.2 cm) diameter upper shaft. The cor rect bracket must be used to ensure that the handlebar is mounted securely to the upper shaft before use. 4 ScrewMountingBracketHandlebarBracketCoverScrewMountingBracketHandlebarBracketCover 1. Place the mounting bracket over the upper shaft above the arrow on the safety label. Be sure to use the correct mounting bracket for either the 1. (2.5 cm) or 7/8. (2.2 cm) diameter upper shaft. 2. Position one of the bracket covers under the upper shaft and align the mounting bracket and the bracket cover screw holes. Insert two screws into the screw holes. 3. Secure the mounting bracket by tightening the screws with the hex wrench. 4. Locate the decal on the handlebar. This decal includes an arrow. Position the handlebar with the mounting bracket at the end of the arrow. 5. Position the second bracket cover over the handlebar. Align the mounting bracket and the bracket cover screw holes. Again make sure the handlebar is at the end of the arrow. 6. Insert two screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the hex wrench. SHOULDER STRAP ASSEMBLY WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit. The shoulder strap clamp must be installed as shown above the handlebar on the upper shaft (powerhead end of unit). NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1. (2.5 cm)diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1. (2.5 cm) diameter upper shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8. (2.2 cm) upper shaft. LOWER SHOULDER STRAP CLAMP Spacer Tabs SpacerTabspositionedforuseon1.(2.5cm) diameteruppershaft 1. Place the upper shoulder strap clamp over the upper shaft above the handlebar. 2. Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i.e. for 1. (2.5 cm) diameter upper shaft). UpperShoulderStrapClampLowerShoulderStrapClampPOWERHEADENDATTACHMENTEND Screws 3. Insert two screws into the screw holes. 4. Secure shoulder strap clamp by tightening screws with the hex wrench. 5. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoulder strap to all...
Ce manuel est également adapté pour les modèles :Outils de jardin - 530164264 (203.87 kb)