Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit. The shoulder strap clamp must be installed as shown above the handlebar on the upper shaft (powerhead end of unit). NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1. (2.5 cm) diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1. (2.5 cm) diameter upper shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8. (2.2 cm) upper shaft. LOWER SHOULDER STRAP CLAMP Spacer Tabs SpacerTabspositionedforuseon1.(2.5cm) diameteruppershaft 1. Place the upper shoulder strap clamp over the upper shaft above the handlebar. 2. Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i.e. for 1. (2.5 cm) diameter upper shaft). 5. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoulder. 6. Adjust the strap, allowing the hook to be about 6 inches below the waist. 7. Fasten the strap hook to the clamp and lift the tool to the operating position. 8. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit. 30inches(76cm) HARNESSADJUSTMENTFORBALANCE6inches(15cm) belowwaist4--12inches(10--30cm) aboveground 30inches(76cm) 5 OPERATIONOPERATION KNOW YOUR BRUSHCUTTER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. BladeShieldBladeGearboxShaft BLADE TheBLADEisdesignedforcuttinggrass, weeds,andbrushupto1/2inch(1cm)indiameter. WARNING: Always disconnect powerhead spark plug before removing or installing attachments. REMOVING BRUSHCUTTER ATTACHMENT (OR OTHER OPTIONAL ATTACHMENTS) CAUTION: When removing or installing at tachments, place the powerhead and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Upper Shaft TIGHTEN 2. Press and hold the locking/release button. CouplerLOOSENLowerAttachment Knob Locking/ReleaseButtonCouplerUpperShaftLowerAttachment 3.Whilesecurelyholdingtheuppershaft, pulltheattachmentstraightoutofthecoupler. Hanger BLADE SHIELD The BLADE SHIELD provides protection from the spinning blade. INSTALLING OPTIONAL ATTACHMENTS 1. Remove the shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. Primary Hole Coupler GuideRecess Upper Locking/ Attachment Shaft Release Button 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. 6 OPERATING POSITION ALWAYS WEAR: Eye Protection Heavy, Long Pants Boots Cut from your left to your right. NOTE: This brushcutter attachment is not designed for use with electric powerheads. When operating unit with brushcutter attach ment, clip shoulder strap onto upper shoulder strap clamp, stand as shown and check for the following: S Wear eye protection and heavy clothing. S Keep arms extended with right hand holding the trigger handle of powerhead. S Keep left arm extended with left hand holding the handlebar. S Keep unit below waist level. S Shoulder strap pad should be centered on your left shoulder and danger sign centered on your back. S Maintain full weight of tool on left shoulder. S Without bending over, keep the blade near and parallel to the ground and not crowded into material being cut. OPERATING INSTRUCTIONS FOR BRUSHCUTTER ATTACHMENT S Blade Thrust is a reaction that only occurs when using a bladed unit. This reaction can cause serious injury such as amputation. Carefully study this section. It is important that you understand what causes blade thrust, how you can reduce the chance of its occurring, and how you can remain in control of unit if blad...
Ce manuel est également adapté pour les modèles :Outils de jardin - U4000C (139.76 kb)