Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Crank engine a few times to blow excess oil out of plug hole. Then reinstall the plug. 3. Fill fuel tank with fresh gasoline (unless a fuel stabilizer was used). 4. Start the engine outdoors. Do not run engine at high speeds immediately after starting. Check tiller and engine (5-hour care) 1. Check tiller and engine for loose screws, pins, bolts, oil leaks, etc. 2 Clean area around oil fill plug. NOTE Engine must be level. 3. Check/add engine oil as follows: A. Remove oil fill plug. B. Oil level should be almost to top of fill plug hole. If not, add oil using same weight and grade as used at last oil change. C. Reinstall and tighten oil fill plug. Change Engine Oil (25-hour care) NOTE Change oil when unit is level and engine is still warm from operation. Don't pollute: dispose of old oil properly. 1. Clean area around oil fill plug. 2. Remove oil drain plug and allow oil to drain from engine. Tip unit if necessary to be sure oil is completly drained. 3. Reinstall oil drain plug. 4. Remove oil fill plug. NOTE To avoid engine damage, use only quality detergent oil of the correct grade and weight. The grade (service) marking on the can may be SC,SD, SE, or MS. The correct recommended weight is SAE 30 or, if unavailable, SAE 10W-30. 5. Fill crankcase with new oil to overflowing. Pour slowly. Capacity: about 2-3/4 pints (1.3 (_). 6. Reinstall and tighten fill plug. Figure 7. Check/Change Oil 10 Normal Саге fígimaíieseim To check or add worm gear oil: 1. Remove fill plug. NOTE There is a breather in a vent hole at rear of worm drive housing. Do not remove breather for any reason. 2 Oil should be level with plug hole when tines are resting on ground (housing level). If not, add special worm gear oil (available from your dealer) through plug hole until full. Do not overfill. NOTE Damage to the worm gear drive which results from use of any lubricant other than special worm gear oil as specificed by the manufacturer, or its equivalent, will automatically invalidate the warranty. 3. Reinstall and tighten fill plug. NOTE The worm drive housing may become warm from operation. This is completely normal and no harm to gears will occur if the housing is kept full as specified with the special worm gear oil. Figure 8. Check/Add Worm Gear Oil (25-Hour Care) NOTE NOTE Use oil sparingly. Excess oil only collects dirt which causes extra wear. Do not oil wheel bearings. Keep oil off pulleys and belts. Symbol Use Apply With Procedure * Medium weight (SAE 30) oil Oil can 1. Brush and wipe dirt and grass from area. 2. Apply a few drops of oil. 3. Wipe up any drips or spills. Figure 9. Lubrication (25-Hour Care) fmimaÊStsËiu Normal Care 1. Clean ali dirt and grass from engine fins. 2 Clean engine air filter. A. Remove wing nut and cover. B. Lift foam element with cup from base. C. Remove cup from foam element. D. Wash foam in kerosene or liquid detergent and water to remove dirt E. Wrap foam in cloth and squeeze dry. F. Saturate foam with engine oil. Squeeze to remove excess oil. G. Reinstall cup in foam. Be sure foam sealing lip is over both ends of cup. H. Reinstall air filter on engine. — WING NUT -COVER SEALING / LIP ! CUP BASE ! FOAM ELEMENT Figure 10. Clean Engine and Air Filter (25-Hour Care or as Required) 1. Disconnect plug wire and fasten it in V-notch on cylinder cover. See figure 14 if necessary. NOTE Do not clean spark plug by sandblasting; sand or grit that remains on plug may damage engine. 2 Clean spark plug. If plug shows signs of defects, it should be replaced with a new plug. 3. Set gap at .030 inch (.76 mm). 4. Reinstall spark plug and torque it to 19 Ft. Lbs. (25 N-m). Reconnect plug wire. USE SPARK PLUG ADJUSTING TOOL TO SET GAP Figure 11. Clean or Replace Spark Plug (100-Hour Care) ffwimaisssBi lem description that best describes the trouble that you have encountered. Check the possible causes one at a time in the order that they are listed. Correct any problems that are found and try to operate the rotary tiller again to see if you have eliminated the trouble. A WARNING To avoid serious injury, perform maintenance on the tiller only when the engine is stopped. Also, remove the spark plug or remove spark plug wire and insert terminal in V-notch on cylinder cover. (See figure 14 if necessary). Problem Cause/Remedy 1. Engine fails to start. A. Out of fuel. Fill fuel tank. B. Choke lever not on. Move choke to on position and set throttle lever at half speed. C. Spark plug wire off or loose. Install fully. D. Engine flooded. Move choke to off position and try starting engine again. E. Spark plug or points faulty, fouled, or incorrectly gapped. See figure 11 and your engine manual. F. Water in fuel. Drain tank and refill with fresh fuel. G. Old, stale gas. Drain tank and refill with fresh fuel. 2 Engine starts hard or runs poorly. A. Fuel mixture too rich. Be sure choke is off. Clean air filter. B. Spark plug or points faulty, fouled,...