Read and understand the operator’s manual and observe the warnings and instruction labels affixed to the tool. • Do not allow children or untrained individuals to use this unit. • Wear safety glasses or goggles that are marked to comply with ANSI Z87.1 standards and hearing and head protection when operating this unit. • Wear heavy long pants, boots, and gloves. Do not wear loose fitting clothing, short pants, jewelry of any kind, or go barefoot. • Secure long hair so it is above shoulder level

DO NOT OIL SELF-LUBRICATED WHEEL BEARINGS. REPAIRS To prevent rust, sand off and paint any parts or areas which become chipped or damaged. Tighten all bolts, capscrews, nuts, and fasteners securely. OFF-SEASON STORAGE If tiller is to be stored over 30 days proceed as follows: 1. Clean fuel screen and bowl. See Maintenance section of this manual. 2. Drain fuel tank and lines by placing suitable container under fuel shut-off valve and opening valve. Store gasoline in container using a gasoli

Allow no open flame, smoking, or matches near the area when refueling. Replace filler cap securely. Store gasoline only in small quantities. Prolonged storage produces gum and harmful deposits. If it is necessary to store gasoline for long periods, add a gasoline stabilizer. See Off-Season Storage section of this manual. Figure 9. c. OIL. See Figure 10. Have available sufficient quantities of engine crankcase oil, SAE 30 grade MS. Remove dirt around engine filler plug. Remove engine filler pl

TILLER 3H.P. TILLER MFG. NO. 1600399 TINE EXTENSION KIT MFG. NO. 1600407 FURROW OPENER MFG. NO. 1600373 OPERATOR'S RIORUM FORM - 1651763 PRINTED IN U.S.A 748 WARRANTY We warrant this HOMELITE product to be free from defects in material or workmanship under norma! use and service, except that we make no warranty, express or implied, with respect to tires, engines, generators or voltage regulators {which usually are warranted by their respective manufacturers) nor with respect to any unit whi

TILLER MFG. NO. 1600405 8 H.P: TILLER TINE EXTENSION KIT MFG. NO. 1600406 FURROW OPENER MFG. NO. 1600373 OPERHIOR'S mnnum FORM - 1651767 PRINTED IN U.S.A. 749 TABLE OF CONTENTS Page WARRANTY ..............................................Inside Cover SAFETY PRECAUTIONS ........................................ 1 ACCESSORIES .............................................. 2 ASSEMBLING ................................................ 2 OPERATION ............................................

Blade thrust is the reaction which may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust may occur without warning if the blade snags, stalls or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and

5.1 Rear Handle .......................................................................................................................... 6.2 Sound pressure level (in accordance with EN ISO 11806:1997, ISO 7917:1987) ............................................................ 99 Sound power level (in accordance with ISO 10884) ...................................................................................................... 113 5 6 UNPACKING INSTRUCTIONS ¦ Carefully remove the product from

457 mm Engine displacement ................................................................................................................................................ 30 cm3 Maximum engine performance (in accordance with ISO 8893) ............................................................................... 0.78 kW Maximum rotational frequency of the spindle ...................................................................................................10,000/min-1 Engine Speed (rotati

2. Loosen fuel cap slowly to release pressure and to keep fuel from escaping around the cap. 3. Carefully pour fuel mixture into the tank. Avoid spillage. 4. Prior to replacing the fuel cap, clean and inspect the gasket. 5. Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. Move 9 m (30 ft) away from refuelling site before starting engine. NOTE: It is normal for smoke to be emitted from a new engine during and after first use. WARNING: Always shut off engine before refuell

24666 ■ Read the Owner's Manual carefully. Be thoroughly familiar with the controls and proper use of the equipment. ■ Never allow children to operate the unit. ■ Keep the area of operation clear of all persons, particularly small children, and pets. ■ Thoroughly inspect the area where the equipment is to be used and remove all stones, wire, bones and other foreign objects. ■ Do not operate equipment when barefoot or wearing open sandals. Always wear substantial footwear. ■ Check fuel befo