Log:
Évaluations - 4, GPA: 3.5 ( )

Instructions American Standard, Modèle TROPIC CADET 2457

Fabricant : American Standard
Taille : 140.15 kb
Nom Fichier : Install_1970.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up! CLOSET BOLT NUT TAPERED WASHER FLANGE INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall. For 4007 Tanks: 12" (305mm) ROUGHING-IN DIMENSIONS: NOTE: Distance from wall to closet flange centerline must be as listed below: © AS America, Inc. 2011 RUBBER GASKET TANK MTG. BOLTS PREINSTALLED 6 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant. INSTALL TANK a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nut combo. b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface. CLOSET FLANGE CLOSET BOLT NUTWASHER BOLT CAP WASHER/ NUT COMBO ! ! CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed). USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.* 6 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant. INSTALL TANK a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nut combo. b. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface. CLOSET FLANGE CLOSET BOLT NUTWASHER BOLT CAP WASHER/ NUT COMBO ! ! CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed). USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.* 8 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. 9a 9bBefore continuing, determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings. CAUTION: DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE. These parts must be use...

Ce manuel est également adapté pour les modèles :
Plomberie - TROPIC CADET 2492 (140.15 kb)
Plomberie - TROPIC CADET 2455 (140.15 kb)
Plomberie - TROPIC CADET 2490 (140.15 kb)
Plomberie - TROPIC CADET 2455 (140.15 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories