Log:
Évaluations - 3, GPA: 5 ( )

Instructions Hans Grohe, Modèle Talis S Electronic Faucet 32112XX1

Fabricant : Hans Grohe
Taille : 1.67 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Due to air in the faucet, the spray pattern may be unattractive for the first 10 - 15 uses after installation or service. 32110XX1/32112XX1 only: pull the temperature lever forward to make the water cooler, backward to make it warmer. 3 4 1 2 Temperature adjustment - 32111XX1 / 32113XX1 only Turn the water supplies off (1). Disconnect the faucet power cable from the battery pack or AC power pack (2). Remove the screw from the rear of the faucet (3). 3 2 1 Remove the faucet body (1). Turn the temperature screw forward to make the water cooler, backward to make it warmer (2). Dry any drops of water from the faucet or mounting surface. Replace the faucet body (1). Replace the screw (2). Turn the water supplies on (3). Reconnect the power cable (4). Wait 30 seconds (1). Place your hand in front of the faucet to turn it on (2). 1 2 1 2 3 4 Battery replacement -- models 32110XX1 / 32111XX1 only If the LED in the sensor window flashes, the battery is low, but the faucet can still be used. If the LED lights continuously, the battery must be changed before the faucet can be used. Remove the four screws and the battery pack cover. Remove the old battery (1). Install the new battery (2). Reinstall the battery pack cover. Wait 30 seconds (1). Activate the faucet by placing a hand in front of the sensor (2). 2 1 Clean the aerator and filters -- all models If the water flow is reduced over time, clean the aerator (a) and the filters (b). Turn the water supplies off (1). Disconnect the power cable (2). Unscrew the aerator (a) with the service key. Disconnect the hot and cold supply hoses from the adapters. Remove the filters (b). At another sink, rinse the filters and the aerator. Reinstall the aerator. Replace the filters. Reconnect the hot and cold supply hoses (see page 4). Turn the water on (1). Reconnect the power cable (2). a b 2 1 1 2 Wait 30 seconds (1). Place a hand in front of the sensor to turn the faucet on (2). Cleaning The faucet may be turned off temporarily so that the sink may be cleaned. Cover the sensor window with a hand for approximately 10 seconds. The faucet will turn off for approximately 60 seconds, so that the sink may be cleaned. The LED in the sensor window will flash. When the LED no longer flashes, the faucet may be used normally. Reduce the sensor range The sensor is set for maximum range at the factory. If the faucet is used on a very small or highly reflective lavatory, the sensor range may be reduced by approximately 2”. Disconnect the power cable for approximately 10 seconds (1). Reconnect the power cable (2). The LED will blink once to indicate that it is in the “maximum range” mode. When the LED stays on, cover the sensor window with your hand or with a white card for 20 - 40 seconds to reset the electronics*. When the hand or card is removed, the LED will blink -- once for “maximum range”, twice for “reduced range”. The LED will then stay on while the sensor recalibrates itself. When the LED turns off, the faucet is ready f...

Ce manuel est également adapté pour les modèles :
Plomberie - Talis S Electronic Faucet 32110XX1 (1.67 mb)
Plomberie - Talis S Electronic Faucet 32110XX1 (1.67 mb)
Plomberie - Talis S Electronic Faucet 32110XX1 (1.67 mb)
Plomberie - Talis S Electronic Faucet 32112XX1 (1.67 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories