Évaluations - 4, GPA: 4 ( )

Fabricant : Wayne Taille : 834.72 kb Nom Fichier : Langue d'enseignement:

2. Disassembly of the motor prior to expiration of warranty will void the warranty. If repairs are required, see troubleshooting chart. 3. Inlet should be kept clean and free of all foreign objects and inspect annually. A clogged inlet will damage pump. 4. Pump should be checked monthly for proper operation. This pump contains dielectric oil for cooling. This oil can be harmful to the environment. Check the state environmental laws before disposing this oil. Figure 6 - Duplex System Off Level On Level Alarm Level Pump #1 Discharge Pump #2 Discharge 4 Operating Instructions and Parts Manual Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Pump will not start or run 1. Blown fuse, tripped breaker 1. If blown, replace with proper sized fuse or reset breaker 2. Low line voltage 2. If voltage is under 108 volts, check wiring size 3. Defective motor 3. Replace pump 4. Defective float switch 4. Replace float switch 5. Stuck/ jammed impeller 5. If impeller will not turn, remove housing and remove blockage 6. Float obstructed 6. Make sure float(s) move freely up and down Pump starts and stops too 1. Back-flow of water from 1. Install or replace check valve often piping 2. Faulty float switch 2. Replace float switch Pump will not shut off or 1. Defective float switch 1. Replace float switch thermal protector turns off 2. Obstacle in piping 2. Remove pump and clean pump and piping 3. Float obstructed 3. Make sure float move freely up and down 4. Low line voltage 4. If voltage is under 108 volts, check wiring size 5. Too many appliances on 5. Install pump on dedicated circuit. IMPORTANT: Do not circuit use extension cord to power pump. Pump operates but delivers 1. Plugged impeller 1. Clean out impeller little or no water 2. Check valve installed 2. Reverse position of check valve backwards 3. Pump air locked 3. Check the 1/8 in. hole in discharge line between pump and check valve; it should be 1 in. to 2 in. above discharge flange and before the check valve 5 6 For Replacement Parts or Technical Assistance, Call 1-800-237-0987 Please provide following information: Address any correspondence to: - Model number Wayne Water Systems - Serial number (if any) 101 Production Drive - Part description and number as shown in parts list Harrison, OH 45030 U.S.A. Operating Instructions and Parts Manual Ref. No. Description Part Number Qty 1 Pipe plug 1/4 in. NPT 16314 1 2 Lifting eye 23124 1 3 Motor SEE CHART 1 4 Reducer bushing 3 in. NPT - 2 in. NPT 17436-001 1 5 1/2 - 13 UNC x 2 1/4 Hex head 16636 2 6 Discharge flange 3 in. 23100 1 7 3 in. Discharge gasket 23102 1 8 Washer 16635 4 9 1/2 - 13 UNC Hex nut 16637 2 10 Volute 56603 1 11 Volute wear ring 23112 1 12 Impeller SEE CHART 1 13 Volute gasket 16735 1 14 Shaft seal kit 56884-002 1 15 Seal plate 56604 1 16 Cover gasket 16855 1 17 Capacitor 3/4 HP to 2 HP 1/2 HP only 23126 23126-002 11 Ref. No. Description Part Number Qty 18 Motor housing 41048-001 1 19 3/8 - 16 UNC x 1 1/4 Socket head 16798 3 20 1/2 -13 UNC x 2 1/4 Hex head 16636 4 21 Screw, 10 - 24 x 1/2 67050-001 2 22 Power supply cord 1/2 HP 3/4 HP - 2 HP 31036-001 31036-002 11 23 Locking cable tie (not shown) 17182-003 3 24 Dielectric oil - 1 gallon (not shown) 56435 1 MOTOR / IMPELLER CHART HP Motor Part Number Impeller Part Number 1/2 3710-004 84341 3/4 3710-005 84342 1 3710-006 84343 2 3710-008 84345 1 2 4 5 6 7 8 9 10 12 11 13 14 15 16 17 19 18 20 21 22 3 Operating Instructions and Parts Manual Notes 7 Operating Instructions and Parts Manual Limited Warranty For one (1) year from the date of purchase, Wayne Water Systems will repair or replace, at its option, for the original purchaser any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :