Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Phoebe Micro, Inc. Preface FCC Warning This device has been tested and found to comply with limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the user’s manual, may cause interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. 1 Introduction Introduction Congratulations on your purchase of the 16-Port 10/100/1000Mbps Green Switch! It is an easy-installed network switch which helps you to extend your network structure quickly and reliably. The 16-Port 10/100/1000Mbps Green Switch is designed for energy saving, easy installation and high performance in an environment where network traffic and the number of users increase continuously. You can add other Ethernet devices like computers, IP cameras, and Network Attached Storage (NAS) onto your network quickly and easily. The Green EEE (Energy Efficient Ethernet) technology of AGSW1600 automatically reduces the power usage when a connected port is detected inactive (idle or cable-unplugged) and intelligently allocates less power for a port that connects with an Ethernet cable shorter than 20m (66 ft)*. Before you begin the installation, please check the items of your package: Package Contents: • 16-Port 10/100/1000Mbps Green Switch • Power Cord • Quick Installation Guide • Brackets and Screws 2 Section 1 Section 1 Hardware Description 1.1 Hardware Interface • 16-Port 10/100/1000Mbps auto-negotiation RJ45 Ports • All ports support auto MDI/MDIX, no need to use cross-over cables 1.2 Panel 1.2.1 Front Panel The front panel of the Switch consists of LED indicators, and 16 10/100/1000Mbps ports. The figure below shows the front panel of the Switch. Figure 1-1 Front Panel view of the Switch • 10/100/1000Mbps Ports (Port 1~16): These ports support 10/100/1000Mbps, and can operate in Half/Full Duplex transfer modes. These ports also support automatic MDI/MDI-X crossover detection, giving true “plug and play” capability. • LED Indicators: Comprehensive LED indicators display the status of the Switch and the network (see Section 1.2.3). 3 1.2.2 Rear Panel Figure 1-2 Rear Panel view of the Switch • AC Power Connector: Supports AC 100~240V, 50~60Hz. NOTICE: Do not cover or put anything on or surrounding the Switch while the Switch is operating. 1.2.3 LED indicators information The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed. Figure 1-3 Front Panel view of the Switch 4 • POWER: Power Indicator LED Color Status Solid Blinking Off POWER Green The Switch is power-on N/A No power • Port 1~16 10/100/1000Mbps Status LEDs LED Color Status Solid Blinking Off LINK/ ACT 10/100M Green The respective port is successfully connected to the 10/100Mbps Ethernet network The port is transmitting or receiving data at 10/100Mbps No link LED Color Status Solid Blinking Off LINK/ ACT 1000M Blue The respective port is connected to the 1000Mbps Ethernet network The port is transmitting or receiving data at above 100Mbps No link 5 Section 2 Section 2 Installing the Switch The site where you place the Switch may greatly affect its performance. 2.1 Installation Please follow the guidelines below to install the Switch: • Please install the Switch in a fairly cool and dry place. Please refer to the Technical Specifications for the acceptable temperature and humidity operating ranges. • Please install the Switch on a sturdy, level surface that can support its weight. • When connecting the power cord to the Switch and the power outlet, the distance should be no more than 182cm. • Please leave at least 10cm (about 4 inches) of space at the front and rear of the Switch for ventilation. 2.2 Desktop or Shelf Installation When installing the Switch on the desktop or shelf, please attach the rubber feet to the Switch. Peel off the protective paper on the pads and attach them to the bottom of the Switch (one at each corner). 6 2.3 Rack Installation The Switch is rack-mountable and can be installed on an EIA 11-inch equipment rack. To do this, first install the mounting brackets on the Switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the Switch. 2.4 Power on the Switch The Switch has a universal power su...