Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
The load attached to the ZRW113 is not affected. If you associate Z-Wave devices into Group 3, you can turn those devices on or off by tapping the switch on or off three times. You can brighten or dim devices by tapping the switch on or off twice and then holding the switch. The load attached to the ZRW113 is not affected. You can associate up to 5 Z-Wave devices into each of these groups. For instructions on how to “associate” a Z-Wave device into one of these groups, refer to your wireless controller instructions. (If you are using the ZTH100 controller, refer to the Setup Menu, Association section). A NOTE ABOUT DIMMING: If you combine Z-Wave enabled dimmers and other types of Z-Wave devices in a group, place a Z-Wave enabled dimmer into the empty group 1st to ensure that the dimming operates correctly. Configuration The ZRW113 supports the Configuration command. The ZRW113 can be configured to operate slightly differently than how it works when you first install it. Using the Configuration command you can configure the following: You can use a ZTH100 to send Configuration commands. (Refer to the Setup Menu, Configuration section) Set Ignore Start Level Bit When Transmitting Dim Commands The ZRW113 can send Dim commands to Z-Wave enabled dimmers. The Dim command has a start level embedded in it. A dimmer receiving this command will start dimming from that start level if this bit is set to 0. If the bit is set to 1, the dimmer will ignore the start level and instead start dimming from its current level. • Parameter No: 1 • Length: 1 Byte • Valid Values = 0 or 1 (default 1) Night Light The LED on the ZRW113 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1. • Parameter No: 3 • Length: 1 Byte • Valid Values = 0 or 1 (default 0) Invert Switch To change the top of the switch to OFF and the bottom of the switch ON , set parameter 4 to 1. • Parameter No: 4 • Length: 1 Byte • Valid Values = 0 or 1 (default 0) LED Transmission Indication The ZRW113 will flicker its LED when it is transmitting to any of its 2 groups. This flickering can be set to not flicker at all (set to 0), to flicker the entire time it is transmitting (set to 1), or to flicker for only 1 second when it begins transmitting (set to 2). By default, the ZRW113 is set to flicker for only 1 second. • Parameter 19 • Length: 1 Byte • Valid Values = 0 , 1, 2 (default 2) Each Configuration Parameter can be set to its default setting by setting the default bit in the Configuration Set command. See your controller’s instructions on how to do this (and if it supports it). All Configuration commands will be reset to their default state when the ZRW113 isRESET from the Z-Wave system. HomePro 0766-01 Z-Wave ZRW113 Instructions, Series 200, Release 2.2 by ADVANCED CONTROL TECHNOLOGIES, INC. 3 P/D 011008 SUC Support There must be a Static Update Controller in your Z-Wave system for this feature to work. The Static Controller can act as a gateway in the system, since other nodes always know its position (not moved after addition to the network. The “always listening” advantage of the Static Controller is that other nodes can transmit information frames to it whenever needed. You can assign an “SUC Route” to the ZRW113. Refer to your controller’s instructions on how to do this (if it supports it). Assigning an SUC Route to the ZRW113 allows it to request an update of the Z-Wave devices that are between it and the Z-Wave device to which it was trying to transmit. The ZRW113 will only request an update when a transmission fails. SPECIFICATIONS Power: 120 VAC, 60 Hz Signal (Frequency): 908.42 MHz Maximum Load -Isolated Contacts: 20 amps (5440 watts) maximum, 277 VAC Motor: 1 H.P. maximum, 120/240 VAC Incandescent: TV8 (Tungsten), 120 VAC, 960W maximum Range: Up to 100 feet line of sight between the Wireless Controller and /or the closest HomePro Receiver Module INTEROPERABILITY WITH Z-WAVE™ DEVICES A Z-Wave™ network can integrate devices of various classes, and these devices can be made by different manufacturers, just as the ZRW113 can be incorporated into existing Z-Wave™ networks. The top or bottom of the paddle switch on the ZRW113 can be used to carry out inclusion (adding to the network by adding to a group), association (operate simultaneously with other nodes), exclusion (remove from a group) or reset (remove from the network). Controllers can be replicated in order to provide operation from various locations. WARRANTY For warranty and general product information visit our web site at ABOUT ZRW113’S CERTIFICATION The ZRW113 is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interfer...
Ce manuel est également adapté pour les modèles :Matériel de réseau - ZRW113 (292.22 kb)